-- ***************************************************************** -- Cisco VTP MIB -- -- February, 1997 Chris Young -- April, 2003 Wen Xu -- July, 2003 Wen Xu -- August, 2003 Wen Xu -- November, 2003 Wen Xu -- February, 2004 Wen Xu -- -- Copyright (c) 1996-2013 by Cisco Systems Inc. -- All rights reserved. -- ***************************************************************** -- CISCO-VTP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Counter32, IpAddress, Gauge32, Integer32, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION, RowStatus, DisplayString, DateAndTime, TruthValue, TestAndIncr, TimeStamp FROM SNMPv2-TC InterfaceIndex, ifIndex, InterfaceIndexOrZero FROM IF-MIB InetAddress, InetAddressType FROM INET-ADDRESS-MIB OwnerString FROM RMON-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB Cisco2KVlanList FROM CISCO-TC ciscoMgmt FROM CISCO-SMI; ciscoVtpMIB MODULE-IDENTITY LAST-UPDATED "201310140000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-wbu@cisco.com, cs-lan-switch-snmp@cisco.com" DESCRIPTION "The MIB module for entities implementing the VTP protocol and Vlan management." REVISION "201310140000Z" DESCRIPTION "Added following OBJECT-GROUP - vtpSourceInterfaceGroup - vtpConfigFileGroup - vtpVlanLocalShutdownGroup - vtpLocalUpdaterGroup - vtpDeviceIdGroup Added new compliance - vtpMIBCompliance16." REVISION "201005120000Z" DESCRIPTION "Added vlanTrunkPortActiveVlansGroup. Updated the description of vtpServerDisabled." REVISION "200912030000Z" DESCRIPTION "Added vtpTrunkPruningGroup3 and vtpConfigNotificationsGroup8. Modified the description of vtpNotificationsEnabled and managementDomainPruningState." REVISION "200803070000Z" DESCRIPTION "Added vlanStatsGroup. Deprecated vtpConfigNotificationsGroup5 and replaced it with vtpConfigNotificationsGroup6 and vtpConfigNotificationsGroup7." REVISION "200710040000Z" DESCRIPTION "Correct the descriptions of the object vtpConfigDigestErrors and the tables vtpVlanTable and vtpInternalVlanTable." REVISION "200602170000Z" DESCRIPTION "Removed the OwnerString TEXTUAL-CONVENTION and imported the same from RMON-MIB." REVISION "200402110000Z" DESCRIPTION "Added 'dynamicGvrp(4)' for the TC VlanTypeExt." REVISION "200311210000Z" DESCRIPTION "Add vtpInternalVlanGrp to configure internal VLANs' allocation policy and show the owner application names." REVISION "200308080000Z" DESCRIPTION "Split vtpConfigNotificationsGroup into two groups: vtpConfigNotificationsGroupRev1 and vtpConfigNotificationsGroup5. Write a new compliance statement to list vtpConfigNotificationsGroupRev1 in instead of vtpConfigNotificationsGroup in the MANDATORY-GROUPS." REVISION "200307110000Z" DESCRIPTION "Modify the description of the TC VlanIndex." REVISION "200304160000Z" DESCRIPTION "Add support for VTP version 3 features. -- Add enumerators and modify the 'DESCRIPTION' of 6 existing objects: vtpVersion, managementDomainLocalMode, managementDomainConfigRevNumber, managementDomainLastUpdater, managementDomainLastChange, managementDomainVersionInUse. -- Add 3 new groups: vtpAuthGroup, vtpDiscoverGroup, vtpDatabaseGroup." REVISION "200204100000Z" DESCRIPTION "-- Add 4 new notifications/traps vtpLocalModeChanged, vtpVersionInUseChanged, vtpVlanCreated and vtpVlanDeleted. -- Add 2 new objects vtpVlanCreatedNotifEnabled and vtpVlanDeletedNotifEnabled to control the generation of vtpVlanCreated and vtpVlanDeleted. -- Use vtpNotificationsEnabled to control the generation of vtpLocalModeChanged and vtpVersionInUseChanged by grouping them in a new group vtpConfigNotificationsGroup2. -- Deprecate the object vlanTrunkPortsDot1qTag and its related group." REVISION "200202280000Z" DESCRIPTION "Deprecate the object, vlanTrunkPortDot1qTunnel." REVISION "200108030000Z" DESCRIPTION "Add a new off(4) mode to managementDomainLocalMode." REVISION "200102260000Z" DESCRIPTION "Deprecate read-only object vtpVlanEditTypeExt and add a new read-create object vtpVlanEditTypeExt2. Enable Notification groups." REVISION "200102120000Z" DESCRIPTION "Added Remote SPAN (RSPAN) VLAN feature, VLAN management features without supporting VTP protocol and a new object to handle one-VLAN-editing." REVISION "200009190000Z" DESCRIPTION "Added the mapping from VLAN ID to its corresponding ifIndex" REVISION "200004100000Z" DESCRIPTION "Added 4k VLAN editing and Dot1qTunnel support" REVISION "200001060000Z" DESCRIPTION "Added 4k VLAN support" REVISION "9902251130Z" DESCRIPTION "Added import of NOTIFICATION-GROUP" REVISION "9901051130Z" DESCRIPTION "Added support for encapsulation type notApplicable" REVISION "9805191130Z" DESCRIPTION "Added support for encapsulation type negotiation" REVISION "9708081138Z" DESCRIPTION "Added Backup CRF object" REVISION "9705091130Z" DESCRIPTION "Added ARE and STE hop counts." REVISION "9702241115Z" DESCRIPTION "Added support for turning on VTP for Trunk cards." REVISION "9701271730Z" DESCRIPTION "Added support for version 2 features." REVISION "9609161230Z" DESCRIPTION "Updated the Token-Ring support." REVISION "9607171230Z" DESCRIPTION "Updated to include objects in support of VTP pruning." REVISION "9601181820Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 46 } vtpMIBObjects OBJECT IDENTIFIER ::= { ciscoVtpMIB 1 } -- Textual Conventions VlanIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The VLAN-id of a VLAN on ISL or 802.1q trunks. Modification of default parameters is allowed. Implementations are allowed to restrict the range of VLANs. For entities support up to 1024 VLANS. VLANs above 1000 are reserved for default VLANs and future use. Modification of default parameters is allowed. Creation or deletion of VLANs above 1000 is not allowed. For a new object which needs the vlan-id of a VLAN as its SYNTAX, it is suggested to import VlanIndex from Q-BRIDGE-MIB instead of importing this TC here in CISCO-VTP-MIB." SYNTAX Integer32 (0..4095) ManagementDomainIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An arbitrary integer-value to uniquely identify a management domain on the local system." SYNTAX Integer32 (1..255) VlanType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The type of a VLAN. Note that the 'ethernet' type, is used for any ethernet or 802.3 VLAN, including an ATM Ethernet ELAN; and the 'tokenRing' ('trCrf') type is used for each VLAN representing a single logical 802.5 ring including an ATM Token-Ring ELAN. The 'trCrf' type is used for token ring VLANs made up of (at most) one transparently bridged LAN segment. The 'trBrf' type is used for VLANs which represent the scope of many 'trCrf' VLANs all connected together via source route bridging. The token ring 'trBrf' can be said to represent the bridged broadcast domain." SYNTAX INTEGER { ethernet(1), fddi(2), tokenRing(3), -- also known as trCrf fddiNet(4), trNet(5), -- also known as trBrf deprecated(6) } VlanTypeExt ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The additional type information of VLAN. vtpmanageable(0) An user defined VLAN which is manageable through VTP protocol. The value of this bit cannot be changed. internal(1) An internal VLAN created by the device. Internal VLANs cannot be created or deleted. The value of this bit cannot be changed. reserved(2) A VLAN reserved by the device. Reserved VLANs cannot be created or deleted. The value of this bit cannot be changed. rspan(3) A VLAN created to exclusively carry the traffic for a Remote Switched Port Analyzer (RSPAN). This bit can only be set or cleared during the VLAN creation. Once the VLAN is created, the value of this bit cannot be modified. dynamicGvrp(4) A VLAN dynamically created by GVRP (GARP VLAN Registration Protocol) propagation. The value of this bit cannot be changed." REFERENCE "RFC2674." SYNTAX BITS { vtpmanageable(0), internal(1), reserved(2), rspan(3), dynamicGvrp(4) } -- VTP status vtpStatus OBJECT IDENTIFIER ::= { vtpMIBObjects 1 } vtpVersion OBJECT-TYPE SYNTAX INTEGER { one(1), two(2), none(3), three(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The version of VTP in use on the local system. A device will report its version capability and not any particular version in use on the device. If the device does not support vtp, the version is none(3)." ::= { vtpStatus 1 } vtpMaxVlanStorage OBJECT-TYPE SYNTAX Integer32 (-1..1023) MAX-ACCESS read-only STATUS current DESCRIPTION "An estimate of the maximum number of VLANs about which the local system can recover complete VTP information after a reboot. If the number of defined VLANs is greater than this value, then the system can not act as a VTP Server. For a device which has no means to calculate the estimated number, this value is -1." ::= { vtpStatus 2 } vtpNotificationsEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "An indication of whether the notifications/traps defined by the vtpConfigNotificationsGroup, vtpConfigNotificationsGroup2, and vtpConfigNotificationsGroup8 are enabled." ::= { vtpStatus 3 } vtpVlanCreatedNotifEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "An indication of whether the notification should be generated when a VLAN is created. If the value of this object is 'true' then the vtpVlanCreated notification will be generated. If the value of this object is 'false' then the vtpVlanCreated notification will not be generated." ::= { vtpStatus 4 } vtpVlanDeletedNotifEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "An indication of whether the notification should be generated when a VLAN is deleted. If the value of this object is 'true' then the vtpVlanDeleted notification will be generated. If the value of this object is 'false' then the vtpVlanDeleted notification will not be generated." ::= { vtpStatus 5 } -- VTP Management Domains vlanManagementDomains OBJECT IDENTIFIER ::= { vtpMIBObjects 2 } managementDomainTable OBJECT-TYPE SYNTAX SEQUENCE OF ManagementDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table containing information on the management domains in which the local system is participating. Devices which support only one management domain will support just one row in this table, and will not let it be deleted nor let other rows be created. Devices which support multiple management domains will allow rows to be created and deleted, but will not allow the last row to be deleted. If the device does not support VTP, the table is read-only." ::= { vlanManagementDomains 1 } managementDomainEntry OBJECT-TYPE SYNTAX ManagementDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about the status of one management domain." INDEX { managementDomainIndex } ::= { managementDomainTable 1 } ManagementDomainEntry ::= SEQUENCE { managementDomainIndex ManagementDomainIndex, managementDomainName DisplayString, managementDomainLocalMode INTEGER, managementDomainConfigRevNumber Gauge32, managementDomainLastUpdater IpAddress, managementDomainLastChange DateAndTime, managementDomainRowStatus RowStatus, managementDomainTftpServer IpAddress, managementDomainTftpPathname DisplayString, managementDomainPruningState INTEGER, managementDomainVersionInUse INTEGER, managementDomainPruningStateOper INTEGER, managementDomainAdminSrcIf SnmpAdminString, managementDomainSourceOnlyMode TruthValue, managementDomainOperSrcIf SnmpAdminString, managementDomainConfigFile SnmpAdminString, managementDomainLocalUpdaterType InetAddressType, managementDomainLocalUpdater InetAddress, managementDomainDeviceID SnmpAdminString } managementDomainIndex OBJECT-TYPE SYNTAX ManagementDomainIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary value to uniquely identify the management domain on the local system." ::= { managementDomainEntry 1 } managementDomainName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The management name of a domain in which the local system is participating. The zero-length name corresponds to the 'no management-domain' state which is the initial value at installation-time if not configured otherwise. Note that the zero-length name does not correspond to an operational management domain, and a device does not send VTP advertisements while in the 'no management-domain' state. A device leaves the 'no management-domain' state when it obtains a management-domain name, either through configuration or through inheriting the management-domain name from a received VTP advertisement. When the value of an existing instance of this object is modified by network management, the local system should re- initialize its VLAN information (for the given management domain) as if it had just been configured with a management domain name at installation time." ::= { managementDomainEntry 2 } managementDomainLocalMode OBJECT-TYPE SYNTAX INTEGER { client(1), server(2), transparent(3), off(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The local VTP mode in this management domain when managementDomainVersionInUse is version1(1) or version2(2). If managementDomainVersionInUse is version3(4), this object has the same value with vtpDatabaseLocalMode of VLAN database type. - 'client' indicates that the local system is acting as a VTP client. - 'server' indicates that the local system is acting as a VTP server. - 'transparent' indicates that the local system does not generate or listen to VTP messages, but forwards messages. This mode can also be set by the device itself when the amount of VLAN information is too large for it to hold in DRAM. - 'off' indicates that the local system does not generate, listen to or forward any VTP messages." ::= { managementDomainEntry 3 } managementDomainConfigRevNumber OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current Configuration Revision Number as known by the local device for this management domain when managementDomainVersionInUse is version1(1) or version2(2). If managementDomainVersionInUse is version3(4), this object has the same value with vtpDatabaseRevisionNumber of VLAN database type. This value is updated (if necessary) whenever a VTP advertisement is received or generated. When in the 'no management-domain' state, this value is 0." ::= { managementDomainEntry 4 } managementDomainLastUpdater OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP-address (or one of them) of the VTP Server which last updated the Configuration Revision Number, as indicated in the most recently received VTP advertisement for this management domain, when managementDomainVersionInUse is version1(1) or version2(2). If managementDomainVersionInUse is version3(4), this object has the value of 0.0.0.0. Before an advertisement has been received, this value is 0.0.0.0." ::= { managementDomainEntry 5 } managementDomainLastChange OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The time at which the Configuration Revision Number was (last) increased to its current value, as indicated in the most recently received VTP advertisement for this management domain when managementDomainVersionInUse is not version3(4) or in the most recently received VTP VLAN database advertisement for this management domain when managementDomainVersionInUse is version3(4). The value 0x0000010100000000 indicates that the device which last increased the Configuration Revision Number had no idea of the date/time, or that no advertisement has been received." ::= { managementDomainEntry 6 } managementDomainRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row." ::= { managementDomainEntry 7 } managementDomainTftpServer OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP address of a TFTP Server in/from which VTP VLAN information for this management domain is to be stored/retrieved. If the information is being locally stored in NVRAM, this object should take the value 0.0.0.0." ::= { managementDomainEntry 8 } managementDomainTftpPathname OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "The complete pathname of the file at the TFTP Server identified by the value of managementDomainTftpServer in/from which VTP VLAN information for this management domain is to be stored/retrieved. If the value of corresponding instance of managementDomainTftpServer is 0.0.0.0, the value of this object is ignored." ::= { managementDomainEntry 9 } managementDomainPruningState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "An indication of whether VTP pruning is enabled or disabled in this managament domain. This object can only be modified, either when the corresponding instance value of managementDomainVersionInUse is 'version1' or 'version2' and the corresponding instance value of managementDomainLocalMode is 'server', or when the corresponding instance value of managementDomainVersionInUse is 'version3' and the corresponding instance value of managementDomainLocalMode is 'server' or 'client'." ::= { managementDomainEntry 10 } managementDomainVersionInUse OBJECT-TYPE SYNTAX INTEGER { version1(1), version2(2), none(3), version3(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The current version of the VTP that is in use by the designated management domain. This object can be set to none(3) only when vtpVersion is none(3)." ::= { managementDomainEntry 11 } managementDomainPruningStateOper OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether VTP pruning is operationally enabled or disabled in this managament domain." ::= { managementDomainEntry 12 } managementDomainAdminSrcIf OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "The object specifies the interface to be used as the preferred source interface for the VTP IP updater address. A zero length value indicates that a source interface is not specified." ::= { managementDomainEntry 13 } managementDomainSourceOnlyMode OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "The object specifies whether to use only the IP address of managementDomainAdminSrcIf as the VTP IP updater address. 'true' indicates to only use the IP address of managementDomainAdminSrcIf as the VTP IP updater address. 'false' indicates to use the IP address of managementDomainAdminSrcIf as the VTP IP updater address if managementDomainAdminSrcIf is configured with an IP address. Otherwise, the first available IP address of the system will be used." DEFVAL { false } ::= { managementDomainEntry 14 } managementDomainOperSrcIf OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The object indicates the interface used as the preferred source interface for the VTP IP updater address. A zero length string indicates that a source interface is not available." ::= { managementDomainEntry 15 } managementDomainConfigFile OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "The object specifies the file name where VTP configuration is stored in the format of or :[]. can be (but not limited to): flash, bootflash, slot0, slot1, disk0." ::= { managementDomainEntry 16 } managementDomainLocalUpdaterType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The object indicates the type of the Internet address of the preferred source interface for the VTP IP updater. The value of this object is 'unknown' if managementDomainVersionInUse is 'version3' or managementDomainLocalMode is not 'server'." ::= { managementDomainEntry 17 } managementDomainLocalUpdater OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The object indicates the Internet address of the preferred source interface for the VTP IP updater." ::= { managementDomainEntry 18 } managementDomainDeviceID OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The object indicates a value that uniquely identifies this device within a VTP Domain. The value of this object is zero length string if managementDomainVersionInUse is not 'version3'." ::= { managementDomainEntry 19 } -- VLAN information vlanInfo OBJECT IDENTIFIER ::= { vtpMIBObjects 3 } -- Global information on current VLANs -- -- This information is maintained by VTP Clients and VTP Servers vtpVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF VtpVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information on the VLANs which currently exist." ::= { vlanInfo 1 } vtpVlanEntry OBJECT-TYPE SYNTAX VtpVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about one current VLAN. The managementDomainIndex value in the INDEX clause indicates which management domain the VLAN is in." INDEX { managementDomainIndex, vtpVlanIndex } ::= { vtpVlanTable 1 } VtpVlanEntry ::= SEQUENCE { vtpVlanIndex VlanIndex, vtpVlanState INTEGER, vtpVlanType VlanType, vtpVlanName DisplayString, vtpVlanMtu Integer32, vtpVlanDot10Said OCTET STRING, vtpVlanRingNumber Integer32, vtpVlanBridgeNumber Integer32, vtpVlanStpType INTEGER, vtpVlanParentVlan VlanIndex, vtpVlanTranslationalVlan1 VlanIndex, vtpVlanTranslationalVlan2 VlanIndex, vtpVlanBridgeType INTEGER, vtpVlanAreHopCount Integer32, vtpVlanSteHopCount Integer32, vtpVlanIsCRFBackup TruthValue, vtpVlanTypeExt VlanTypeExt, vtpVlanIfIndex InterfaceIndexOrZero } vtpVlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN-id of this VLAN on ISL or 802.1q trunks." ::= { vtpVlanEntry 1 } vtpVlanState OBJECT-TYPE SYNTAX INTEGER { operational(1), suspended(2), mtuTooBigForDevice(3), mtuTooBigForTrunk(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of this VLAN. The state 'mtuTooBigForDevice' indicates that this device cannot participate in this VLAN because the VLAN's MTU is larger than the device can support. The state 'mtuTooBigForTrunk' indicates that while this VLAN's MTU is supported by this device, it is too large for one or more of the device's trunk ports." ::= { vtpVlanEntry 2 } vtpVlanType OBJECT-TYPE SYNTAX VlanType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of this VLAN." ::= { vtpVlanEntry 3 } vtpVlanName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of this VLAN. This name is used as the ELAN-name for an ATM LAN-Emulation segment of this VLAN." ::= { vtpVlanEntry 4 } vtpVlanMtu OBJECT-TYPE SYNTAX Integer32 (1500..18190) MAX-ACCESS read-only STATUS current DESCRIPTION "The MTU size on this VLAN, defined as the size of largest MAC-layer (information field portion of the) data frame which can be transmitted on the VLAN." ::= { vtpVlanEntry 5 } vtpVlanDot10Said OBJECT-TYPE SYNTAX OCTET STRING (SIZE (4)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the 802.10 SAID field for this VLAN." ::= { vtpVlanEntry 6 } vtpVlanRingNumber OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "The ring number of this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanType has a value of 'fddi' or 'tokenRing' and Source Routing is in use on this VLAN." ::= { vtpVlanEntry 7 } vtpVlanBridgeNumber OBJECT-TYPE SYNTAX Integer32 (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The bridge number of the VTP-capable switches for this VLAN. This object is only instantiated for VLANs that are involved with emulating token ring segments." ::= { vtpVlanEntry 8 } vtpVlanStpType OBJECT-TYPE SYNTAX INTEGER { ieee(1), ibm(2), hybrid(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the Spanning Tree Protocol (STP) running on this VLAN. This object is only instanciated when the value of the corresponding instance of vtpVlanType has a value of 'fddiNet' or 'trNet'. The value returned by this object depends upon the value of the corresponding instance of vtpVlanEditStpType. - 'ieee' indicates IEEE STP is running exclusively. - 'ibm' indicates IBM STP is running exclusively. - 'hybrid' indicates a STP that allows a combination of IEEE and IBM is running. The 'hybrid' STP type results from tokenRing/fddi VLANs that are children of this trNet/fddiNet parent VLAN being configured in a combination of SRT and SRB vtpVlanBridgeTypes while the instance of vtpVlanEditStpType that corresponds to this object is set to 'auto'." ::= { vtpVlanEntry 9 } vtpVlanParentVlan OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The parent VLAN for this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanType has a value of 'fddi' or 'tokenRing' and Source Routing is in use on this VLAN. The parent VLAN must have a vtpVlanType value of fddiNet(4) or trNet(5), respectively." ::= { vtpVlanEntry 10 } vtpVlanTranslationalVlan1 OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "A VLAN to which this VLAN is being translational-bridged. If this value and the corresponding instance of vtpVlanTranslationalVlan2 are both zero, then this VLAN is not being translational-bridged." ::= { vtpVlanEntry 11 } vtpVlanTranslationalVlan2 OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Another VLAN, i.e., other than that indicated by vtpVlanTranslationalVlan1, to which this VLAN is being translational-bridged. If this value and the corresponding instance of vtpVlanTranslationalVlan1 are both zero, then this VLAN is not being translational-bridged." ::= { vtpVlanEntry 12 } vtpVlanBridgeType OBJECT-TYPE SYNTAX INTEGER { srt(1), srb(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the Source Route bridging mode in use on this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanType has a value of fddi(2) or tokenRing(3) and Source Routing is in use on this VLAN." ::= { vtpVlanEntry 13 } vtpVlanAreHopCount OBJECT-TYPE SYNTAX Integer32 (1..13) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of bridge hops allowed in All Routes Explorer frames on this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanType has a value of fddi(2) or tokenRing(3) and Source Routing is in use on this VLAN." ::= { vtpVlanEntry 14 } vtpVlanSteHopCount OBJECT-TYPE SYNTAX Integer32 (1..13) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of bridge hops allowed in Spanning Tree Explorer frames on this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanType has a value of fddi(2) or tokenRing(3) and Source Routing is in use on this VLAN." ::= { vtpVlanEntry 15 } vtpVlanIsCRFBackup OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "True if this VLAN is of type trCrf and also is acting as a backup trCrf for the ISL distributed BRF" ::= { vtpVlanEntry 16 } vtpVlanTypeExt OBJECT-TYPE SYNTAX VlanTypeExt MAX-ACCESS read-only STATUS current DESCRIPTION "The additional type information of this VLAN." ::= { vtpVlanEntry 17 } vtpVlanIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the ifIndex corresponding to this VLAN ID. If the VLAN ID does not have its corresponding interface, this object has the value of zero." ::= { vtpVlanEntry 18 } internalVlanInfo OBJECT IDENTIFIER ::= { vlanInfo 2 } vtpInternalVlanAllocPolicy OBJECT-TYPE SYNTAX INTEGER { ascending(1), descending(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The internal VLAN allocation policy. 'ascending' - internal VLANs are allocated starting from a lowwer VLAN ID and upwards. 'descending' - internal VLANs are allocated starting from a higher VLAN ID and downwards." ::= { internalVlanInfo 1 } vtpInternalVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF VtpInternalVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A vtpInternalVlanTable entry contains information on an existing internal VLAN. It is internally created by the device for a specific application program and hence owned by the application. It cannot be modified or deleted by (local or network) management." ::= { internalVlanInfo 2 } vtpInternalVlanEntry OBJECT-TYPE SYNTAX VtpInternalVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about one current internal VLAN." INDEX { managementDomainIndex, vtpVlanIndex } ::= { vtpInternalVlanTable 1 } VtpInternalVlanEntry ::= SEQUENCE { vtpInternalVlanOwner SnmpAdminString } vtpInternalVlanOwner OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The program name of the internal VLAN's owner application. This internal VLAN is allocated by the device specifically for this application and no one else could create, modify or delete this VLAN." ::= { vtpInternalVlanEntry 1 } -- Modification of Global VLAN Information -- -- To change the global information on current VLANs, including -- creating, modifying or deleting them, -- . the current VLAN information is copied to the "Edit buffer", -- . the information in the Edit buffer is modified as appropriate, -- . an 'apply' is invoked to attempt to instanciate the modified -- contents of the Edit Buffer as the new global VLAN information. -- -- Only one manager can edit the Edit Buffer at a time. So, a -- request to copy the current VLAN information into the Edit Buffer -- must fail if the Edit Buffer is already in use (i.e., is not empty). -- Thus, concurrent attempts by multiple managers to gain use of the -- Edit Buffer are resolved according to whichever of them succeeds -- in performing a successful copy. An OwnerString object provides -- information on which manager currently has access. -- -- Ownership of the Edit Buffer terminates when a NMS explicitly -- releases it, or when a deadman-timer expires. The deadman-timer -- has a fixed expiry interval of 5 minutes. The deadman-timer is -- automatically started on a successful copy operation. The -- restartTimer operation allows an NMS to restart the deadman-timer -- if it wishes to retain ownership of the Edit Buffer for longer -- than 5 minutes. The deadman-timer ceases when the apply operation -- is invoked, and is restarted when the apply operation terminates. -- Restarting the deadman-timer after termination of the apply -- operation allows the results of the apply operation to be retained -- until the requesting manager has retrieved them, but for only a -- limited amount of time. -- -- When managementDomainVersionInUse is version1(1) or version2(2), -- the local device with managementDomainLocalMode as server(2) -- could change the global VLAN configuration by editing the VLAN -- information in the edit buffer and then apply it. However, -- when managementDomainVersionInUse is in version3(4), there -- are two different VTP servers, the primary server and the -- secondary server. The global VLAN configuration could only -- be changed by a primary server for VLAN database. The -- secondary server may still do the 'copy' operation and edit -- the VLAN information in the edit buffer. But in order to make -- a possibly successful 'apply' operation, the local device must -- be a VLAN database primary server. Otherwise, the 'apply' will -- fail and vtpVlanApplyStatus will be set to the error status -- 'notPrimaryServer'. vlanEdit OBJECT IDENTIFIER ::= { vtpMIBObjects 4 } vtpEditControlTable OBJECT-TYPE SYNTAX SEQUENCE OF VtpEditControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the means to control the editing of the VLANs for a particular management domain. Each and every entry in this table augments its corresponding entry in the managementDomainTable; thus, an entry in this table is created/deleted only as a by-product of creating/deleting an entry in the managementDomainTable." ::= { vlanEdit 1 } vtpEditControlEntry OBJECT-TYPE SYNTAX VtpEditControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Control information for editing the VLANs in one management domain." AUGMENTS { managementDomainEntry } ::= { vtpEditControlTable 1 } VtpEditControlEntry ::= SEQUENCE { vtpVlanEditOperation INTEGER, vtpVlanApplyStatus INTEGER, vtpVlanEditBufferOwner OwnerString, vtpVlanEditConfigRevNumber Gauge32, vtpVlanEditModifiedVlan VlanIndex } vtpVlanEditOperation OBJECT-TYPE SYNTAX INTEGER { none(1), copy(2), apply(3), release(4), restartTimer(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object always has the value 'none' when read. When written, each value causes the appropriate action: 'copy' - causes the creation of rows in the vtpVlanEditTable exactly corresponding to the current global VLAN information for this management domain. If the Edit Buffer (for this management domain) is not currently empty, a copy operation fails. A successful copy operation starts the deadman-timer. 'apply' - first performs a consistent check on the the modified information contained in the Edit Buffer, and if consistent, then tries to instanciate the modified information as the new global VLAN information. Note that an empty Edit Buffer (for the management domain) would always result in an inconsistency since the default VLANs are required to be present. 'release' - flushes the Edit Buffer (for this management domain), clears the Owner information, and aborts the deadman-timer. A release is generated automatically if the deadman-timer ever expires. 'restartTimer' - restarts the deadman-timer. 'none' - no operation is performed." ::= { vtpEditControlEntry 1 } vtpVlanApplyStatus OBJECT-TYPE SYNTAX INTEGER { inProgress(1), succeeded(2), configNumberError(3), inconsistentEdit(4), tooBig(5), localNVStoreFail(6), remoteNVStoreFail(7), editBufferEmpty(8), someOtherError(9), notPrimaryServer(10) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current status of an 'apply' operation to instanciate the Edit Buffer as the new global VLAN information (for this management domain). If no apply is currently active, the status represented is that of the most recently completed apply. The possible values are: inProgress - 'apply' operation in progress; succeeded - the 'apply' was successful (this value is also used when no apply has been invoked since the last time the local system restarted); configNumberError - the apply failed because the value of vtpVlanEditConfigRevNumber was less or equal to the value of current value of managementDomainConfigRevNumber; inconsistentEdit - the apply failed because the modified information was not self-consistent; tooBig - the apply failed because the modified information was too large to fit in this VTP Server's non-volatile storage location; localNVStoreFail - the apply failed in trying to store the new information in a local non-volatile storage location; remoteNVStoreFail - the apply failed in trying to store the new information in a remote non-volatile storage location; editBufferEmpty - the apply failed because the Edit Buffer was empty (for this management domain). someOtherError - the apply failed for some other reason (e.g., insufficient memory). notPrimaryServer - the apply failed because the local device is not a VTP primary server for VLAN database type when managementDomainVersionInUse is version3(4)." ::= { vtpEditControlEntry 2 } vtpVlanEditBufferOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "The management station which is currently using the Edit Buffer for this management domain. When the Edit Buffer for a management domain is not currently in use, the value of this object is the zero-length string. Note that it is also the zero-length string if a manager fails to set this object when invoking a copy operation." ::= { vtpEditControlEntry 3 } vtpVlanEditConfigRevNumber OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-create STATUS current DESCRIPTION "The Configuration Revision Number to be used for the next apply operation. This value is initialized (by the agent) on a copy operation to be one greater than the value of managementDomainConfigRevNumber. On an apply, if the number is less or equal to the value of managementDomainConfigRevNumber, then the apply fails. The value can be modified (increased) by network management before an apply to ensure that an apply does not fail for this reason. This object is used to allow management control over whether a configuration revision received via a VTP advertisement after a copy operation but before the succeeding apply operation is lost by being overwritten by the (local) edit operation. By default, the apply operation will fail in this situation. By increasing this object's value after the copy but before the apply, management can control whether the apply is to succeed (with the update via VTP advertisement being lost)." ::= { vtpEditControlEntry 4 } vtpVlanEditModifiedVlan OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN-id of the modified VLAN in the Edit Buffer. If the object has the value of zero, any VLAN can be edited. If the value of the object is not zero, only this VLAN can be edited. The object's value is reset to zero after a successful 'apply' operation or a 'release' operation. This object is only supported for devices which allow only one VLAN editing for each 'apply' operation. For devices which allow multiple VLAN editing for each 'apply' operation, this object is not supported." ::= { vtpEditControlEntry 5 } vtpVlanEditTable OBJECT-TYPE SYNTAX SEQUENCE OF VtpVlanEditEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table which contains the information in the Edit Buffers, one Edit Buffer per management domain. The information for a particular management domain is initialized, by a 'copy' operation, to be the current global VLAN information for that management domain. After initialization, editing can be performed to add VLANs, delete VLANs, or modify their global parameters. The information as modified through editing is local to this Edit Buffer. An apply operation using the vtpVlanEditOperation object is necessary to instanciate the modified information as the new global VLAN information for that management domain. To use the Edit Buffer, a manager acts as follows: 1. ensures the Edit Buffer for a management domain is empty, i.e., there are no rows in this table for this management domain. 2. issues a SNMP set operation which sets vtpVlanEditOperation to 'copy', and vtpVlanEditBufferOwner to its own identifier (e.g., its own IP address). 3. if this set operation is successful, proceeds to edit the information in the vtpVlanEditTable. 4. if and when the edited information is to be instantiated, issues a SNMP set operation which sets vtpVlanEditOperation to 'apply'. 5. issues retrieval requests to obtain the value of vtpVlanApplyStatus, until the result of the apply is determined. 6. releases the Edit Buffer by issuing a SNMP set operation which sets vtpVlanEditOperation to 'release'. Note that the information contained in this table is not saved across agent reboots." ::= { vlanEdit 2 } vtpVlanEditEntry OBJECT-TYPE SYNTAX VtpVlanEditEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about one VLAN in the Edit Buffer for a particular management domain." INDEX { managementDomainIndex, vtpVlanEditIndex } ::= { vtpVlanEditTable 1 } VtpVlanEditEntry ::= SEQUENCE { vtpVlanEditIndex VlanIndex, vtpVlanEditState INTEGER, vtpVlanEditType VlanType, vtpVlanEditName DisplayString, vtpVlanEditMtu Integer32, vtpVlanEditDot10Said OCTET STRING, vtpVlanEditRingNumber Integer32, vtpVlanEditBridgeNumber Integer32, vtpVlanEditStpType INTEGER, vtpVlanEditParentVlan VlanIndex, vtpVlanEditRowStatus RowStatus, vtpVlanEditTranslationalVlan1 VlanIndex, vtpVlanEditTranslationalVlan2 VlanIndex, vtpVlanEditBridgeType INTEGER, vtpVlanEditAreHopCount Integer32, vtpVlanEditSteHopCount Integer32, vtpVlanEditIsCRFBackup TruthValue, vtpVlanEditTypeExt VlanTypeExt, vtpVlanEditTypeExt2 VlanTypeExt } vtpVlanEditIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN-id which this VLAN would have on ISL or 802.1q trunks." ::= { vtpVlanEditEntry 1 } vtpVlanEditState OBJECT-TYPE SYNTAX INTEGER { operational(1), suspended(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state which this VLAN would have." DEFVAL { operational } ::= { vtpVlanEditEntry 2 } vtpVlanEditType OBJECT-TYPE SYNTAX VlanType MAX-ACCESS read-create STATUS current DESCRIPTION "The type which this VLAN would have. An implementation may restrict access to this object." DEFVAL { ethernet } ::= { vtpVlanEditEntry 3 } vtpVlanEditName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The name which this VLAN would have. This name would be used as the ELAN-name for an ATM LAN-Emulation segment of this VLAN. An implementation may restrict access to this object." ::= { vtpVlanEditEntry 4 } vtpVlanEditMtu OBJECT-TYPE SYNTAX Integer32 (1500..18190) MAX-ACCESS read-create STATUS current DESCRIPTION "The MTU size which this VLAN would have, defined as the size of largest MAC-layer (information field portion of the) data frame which can be transmitted on the VLAN. An implementation may restrict access to this object." DEFVAL { 1500 } ::= { vtpVlanEditEntry 5 } vtpVlanEditDot10Said OBJECT-TYPE SYNTAX OCTET STRING (SIZE (4)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of the 802.10 SAID field which would be used for this VLAN. An implementation may restrict access to this object." ::= { vtpVlanEditEntry 6 } vtpVlanEditRingNumber OBJECT-TYPE SYNTAX Integer32 (0..4095) MAX-ACCESS read-create STATUS current DESCRIPTION "The ring number which would be used for this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanEditType has a value of 'fddi' or 'tokenRing' and Source Routing is in use on this VLAN." ::= { vtpVlanEditEntry 7 } vtpVlanEditBridgeNumber OBJECT-TYPE SYNTAX Integer32 (0..15) MAX-ACCESS read-create STATUS current DESCRIPTION "The bridge number of the VTP-capable switches which would be used for this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanEditType has a value of fddiNet(4) or trNet(5)." ::= { vtpVlanEditEntry 8 } vtpVlanEditStpType OBJECT-TYPE SYNTAX INTEGER { ieee(1), ibm(2), auto(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of the Spanning Tree Protocol which would be running on this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanEditType has a value of fddiNet(4) or trNet(5). If 'ieee' is selected, the STP that runs will be IEEE. If 'ibm' is selected, the STP that runs will be IBM. If 'auto' is selected, the STP that runs will be dependant on the values of vtpVlanEditBridgeType for all children tokenRing/fddi type VLANs. This will result in a 'hybrid' STP (see vtpVlanStpType)." ::= { vtpVlanEditEntry 9 } vtpVlanEditParentVlan OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The VLAN index of the VLAN which would be the parent for this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanEditType has a value of 'fddi' or 'tokenRing' and Source Routing is in use on this VLAN. The parent VLAN must have a vtpVlanEditType value of fddiNet(4) or trNet(5), respectively." ::= { vtpVlanEditEntry 10 } vtpVlanEditRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row. Any and all columnar objects in an existing row can be modified irrespective of the status of the row. A row is not qualified for activation until instances of at least its vtpVlanEditType, vtpVlanEditName and vtpVlanEditDot10Said columns have appropriate values. The management station should endeavor to make all rows consistent in the table before 'apply'ing the buffer. An inconsistent entry in the table will cause the entire buffer to be rejected with the vtpVlanApplyStatus object set to the appropriate error value." ::= { vtpVlanEditEntry 11 } vtpVlanEditTranslationalVlan1 OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-create STATUS current DESCRIPTION "A VLAN to which this VLAN would be translational-bridged. If this value and the corresponding instance of vtpVlanTranslationalVlan2 are both zero, then this VLAN would not be translational-bridged. An implementation may restrict access to this object." DEFVAL { 0 } ::= { vtpVlanEditEntry 12 } vtpVlanEditTranslationalVlan2 OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-create STATUS current DESCRIPTION "Another VLAN, i.e., other than that indicated by vtpVlanEditTranslationalVlan1, to which this VLAN would be translational-bridged. If this value and the corresponding instance of vtpVlanTranslationalVlan1 are both zero, then this VLAN would not be translational-bridged. An implementation may restrict access to this object." DEFVAL { 0 } ::= { vtpVlanEditEntry 13 } vtpVlanEditBridgeType OBJECT-TYPE SYNTAX INTEGER { srt(1), srb(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of Source Route bridging mode which would be in use on this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanEditType has a value of fddi(2) or tokenRing(3) and Source Routing is in use on this VLAN." ::= { vtpVlanEditEntry 14 } vtpVlanEditAreHopCount OBJECT-TYPE SYNTAX Integer32 (1..13) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of bridge hops allowed in All Routes Explorer frames on this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanType has a value of fddi(2) or tokenRing(3) and Source Routing is in use on this VLAN." ::= { vtpVlanEditEntry 15 } vtpVlanEditSteHopCount OBJECT-TYPE SYNTAX Integer32 (1..13) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of bridge hops allowed in Spanning Tree Explorer frames on this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanType has a value of fddi(2) or tokenRing(3) and Source Routing is in use on this VLAN." ::= { vtpVlanEditEntry 16 } vtpVlanEditIsCRFBackup OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "True if this VLAN is of type trCrf and also is acting as a backup trCrf for the ISL distributed BRF. This object is only instantiated when the value of the corresponding instance of vtpVlanEditType has a value of tokenRing(3)." ::= { vtpVlanEditEntry 17 } vtpVlanEditTypeExt OBJECT-TYPE SYNTAX VlanTypeExt MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The additional type information of this VLAN. vtpVlanEditTypeExt object is superseded by vtpVlanEditTypeExt2." ::= { vtpVlanEditEntry 18 } vtpVlanEditTypeExt2 OBJECT-TYPE SYNTAX VlanTypeExt MAX-ACCESS read-create STATUS current DESCRIPTION "The additional type information of this VLAN. The VlanTypeExt TC specifies which bits may be written by a management application. The agent should provide a default value." ::= { vtpVlanEditEntry 19 } vtpVlanLocalShutdownTable OBJECT-TYPE SYNTAX SEQUENCE OF VtpVlanLocalShutdownEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Ths table contains the VLAN local shutdown information within management domain." ::= { vlanEdit 3 } vtpVlanLocalShutdownEntry OBJECT-TYPE SYNTAX VtpVlanLocalShutdownEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing VLAN local shutdown information for a particular VLAN in the management domain. An entry is created if a VLAN which supports local shutdown has been created. An entry is deleted if a VLAN which supports local shutdown has been removed." INDEX { managementDomainIndex, vtpVlanIndex } ::= { vtpVlanLocalShutdownTable 1 } VtpVlanLocalShutdownEntry ::= SEQUENCE { vtpVlanLocalShutdown INTEGER } vtpVlanLocalShutdown OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The object specifies the VLAN local shutdown state." ::= { vtpVlanLocalShutdownEntry 1 } -- VTP Statistics vtpStats OBJECT IDENTIFIER ::= { vtpMIBObjects 5 } vtpStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF VtpStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of VTP statistics." ::= { vtpStats 1 } vtpStatsEntry OBJECT-TYPE SYNTAX VtpStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "VTP statistics for one management domain." AUGMENTS { managementDomainEntry } ::= { vtpStatsTable 1 } VtpStatsEntry ::= SEQUENCE { vtpInSummaryAdverts Counter32, vtpInSubsetAdverts Counter32, vtpInAdvertRequests Counter32, vtpOutSummaryAdverts Counter32, vtpOutSubsetAdverts Counter32, vtpOutAdvertRequests Counter32, vtpConfigRevNumberErrors Counter32, vtpConfigDigestErrors Counter32 } vtpInSummaryAdverts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VTP Summary Adverts received for this management domain." ::= { vtpStatsEntry 1 } vtpInSubsetAdverts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VTP Subset Adverts received for this management domain." ::= { vtpStatsEntry 2 } vtpInAdvertRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VTP Advert Requests received for this management domain." ::= { vtpStatsEntry 3 } vtpOutSummaryAdverts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VTP Summary Adverts sent for this management domain." ::= { vtpStatsEntry 4 } vtpOutSubsetAdverts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VTP Subset Adverts sent for this management domain." ::= { vtpStatsEntry 5 } vtpOutAdvertRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VTP Advert Requests sent for this management domain." ::= { vtpStatsEntry 6 } vtpConfigRevNumberErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of occurrences of configuration revision number errors for this management domain. A configuration revision number error occurs when a device receives a VTP advertisement for which: - the advertisement's Configuration Revision Number is the same as the current locally-held value, and - the advertisement's digest value is different from the current locally-held value." ::= { vtpStatsEntry 7 } vtpConfigDigestErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of occurrences of configuration digest errors for this management domain. A configuration digest error occurs when a device receives a VTP advertisement for which: - the advertisement's Configuration Revision Number is greater than the current locally-held value, and - the advertisement's digest value computed by the receiving device does not match the checksum in the summary advertisement that was received earlier. This can happen, for example, if there is a mismatch in VTP passwords between the VTP devices." ::= { vtpStatsEntry 8 } -- Trunk Ports vlanTrunkPorts OBJECT IDENTIFIER ::= { vtpMIBObjects 6 } vlanTrunkPortTable OBJECT-TYPE SYNTAX SEQUENCE OF VlanTrunkPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table containing information on the local system's VLAN trunk ports." ::= { vlanTrunkPorts 1 } vlanTrunkPortEntry OBJECT-TYPE SYNTAX VlanTrunkPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about one trunk port." INDEX { vlanTrunkPortIfIndex } ::= { vlanTrunkPortTable 1 } VlanTrunkPortEntry ::= SEQUENCE { vlanTrunkPortIfIndex InterfaceIndex, vlanTrunkPortManagementDomain ManagementDomainIndex, vlanTrunkPortEncapsulationType INTEGER, vlanTrunkPortVlansEnabled OCTET STRING, vlanTrunkPortNativeVlan VlanIndex, vlanTrunkPortRowStatus RowStatus, vlanTrunkPortInJoins Counter32, vlanTrunkPortOutJoins Counter32, vlanTrunkPortOldAdverts Counter32, vlanTrunkPortVlansPruningEligible OCTET STRING, vlanTrunkPortVlansXmitJoined OCTET STRING, vlanTrunkPortVlansRcvJoined OCTET STRING, vlanTrunkPortDynamicState INTEGER, vlanTrunkPortDynamicStatus INTEGER, vlanTrunkPortVtpEnabled TruthValue, vlanTrunkPortEncapsulationOperType INTEGER, vlanTrunkPortVlansEnabled2k OCTET STRING, vlanTrunkPortVlansEnabled3k OCTET STRING, vlanTrunkPortVlansEnabled4k OCTET STRING, vtpVlansPruningEligible2k OCTET STRING, vtpVlansPruningEligible3k OCTET STRING, vtpVlansPruningEligible4k OCTET STRING, vlanTrunkPortVlansXmitJoined2k OCTET STRING, vlanTrunkPortVlansXmitJoined3k OCTET STRING, vlanTrunkPortVlansXmitJoined4k OCTET STRING, vlanTrunkPortVlansRcvJoined2k OCTET STRING, vlanTrunkPortVlansRcvJoined3k OCTET STRING, vlanTrunkPortVlansRcvJoined4k OCTET STRING, vlanTrunkPortDot1qTunnel INTEGER, vlanTrunkPortVlansActiveFirst2k Cisco2KVlanList, vlanTrunkPortVlansActiveSecond2k Cisco2KVlanList } vlanTrunkPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of ifIndex for the interface corresponding to this trunk port." ::= { vlanTrunkPortEntry 1 } vlanTrunkPortManagementDomain OBJECT-TYPE SYNTAX ManagementDomainIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The value of managementDomainIndex for the management domain on this trunk port. Devices which support only one management domain will support this object read-only." ::= { vlanTrunkPortEntry 2 } vlanTrunkPortEncapsulationType OBJECT-TYPE SYNTAX INTEGER { isl(1), dot10(2), lane(3), dot1Q(4), negotiate(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of VLAN encapsulation desired to be used on this trunk port. It is either a particular type, or 'negotiate' meaning whatever type results from the negotiation. negotiate(5) is not allowed if the port does not support negotiation or if its vlanTrunkPortDynamicState is set to on(1) or onNoNegotiate(5). Whether writing to this object in order to modify the encapsulation is supported is both device and interface specific." ::= { vlanTrunkPortEntry 3 } vlanTrunkPortVlansEnabled OBJECT-TYPE SYNTAX OCTET STRING (SIZE (128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local system is enabled for sending and receiving frames on that VLAN; if the bit is set to '0', then the system is disabled from sending and receiving frames on that VLAN. To avoid conflicts between overlapping partial updates by multiple managers, i.e., updates which modify only a portion of an instance of this object (e.g., enable/disable a single VLAN on the trunk port), any SNMP Set operation accessing an instance of this object should also write the value of vlanTrunkPortSetSerialNo." ::= { vlanTrunkPortEntry 4 } vlanTrunkPortNativeVlan OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The VlanIndex of the VLAN which is represented by native frames on this trunk port. For trunk ports not supporting the sending and receiving of native frames, this value should be set to zero." ::= { vlanTrunkPortEntry 5 } vlanTrunkPortRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row. In some circumstances, the creation of a row in this table is needed to enable the appropriate trunking/tagging protocol on the port, to enable the use of VTP on the port, and to assign the port to the appropriate management domain. In other circumstances, rows in this table will be created as a by-product of other operations." ::= { vlanTrunkPortEntry 6 } vlanTrunkPortInJoins OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of VTP Join messages received on this trunk port." ::= { vlanTrunkPortEntry 7 } vlanTrunkPortOutJoins OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of VTP Join messages sent on this trunk port." ::= { vlanTrunkPortEntry 8 } vlanTrunkPortOldAdverts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of VTP Advertisement messages which indicated the sender does not support VLAN-pruning received on this trunk port." ::= { vlanTrunkPortEntry 9 } vlanTrunkPortVlansPruningEligible OBJECT-TYPE SYNTAX OCTET STRING (SIZE (128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local system is permitted to prune that VLAN on this trunk port; if the bit is set to '0', then the system must not prune that VLAN on this trunk port. To avoid conflicts between overlapping partial updates by multiple managers, i.e., updates which modify only a portion of an instance of this object (e.g., enable/disable a single VLAN on the trunk port), any SNMP Set operation accessing an instance of this object should also write the value of vlanTrunkPortSetSerialNo." ::= { vlanTrunkPortEntry 10 } vlanTrunkPortVlansXmitJoined OBJECT-TYPE SYNTAX OCTET STRING (SIZE (128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then this VLAN is presently being forwarded on this trunk port, i.e., it is not pruned; if the bit is set to '0', then this VLAN is presently not being forwarded on this trunk port, either because it is pruned or for some other reason." ::= { vlanTrunkPortEntry 11 } vlanTrunkPortVlansRcvJoined OBJECT-TYPE SYNTAX OCTET STRING (SIZE (128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local switch is currently sending joins for this VLAN on this trunk port, i.e., it is asking to receive frames for this VLAN; if the bit is set to '0', then the local switch is not currently sending joins for this VLAN on this trunk port." ::= { vlanTrunkPortEntry 12 } vlanTrunkPortDynamicState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2), desirable(3), auto(4), onNoNegotiate(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "For devices that allows dynamic determination of whether a link between two switches should be a trunk or not, this object allows the operator to mandate the behavior of that dynamic mechanism. on(1) dictates that the interface will always be a trunk. This is the value for static entries (those that show no dynamic behavior). If the negotiation is supported on this port, negotiation will take place with the far end to attempt to bring the far end into trunking state. off(2) allows an operator to specify that the specified interface is never to be trunk, regardless of any dynamic mechanisms to the contrary. This value is useful for overriding the default behavior of some switches. If the negotiation is supported on this port, negotiation will take place with the far end to attempt on the link to bring the far end into non-trunking state. desirable(3) is used to indicate that it is desirable for the interface to become a trunk. The device will initiate any negotiation necessary to become a trunk but will not become a trunk unless it receives confirmation from the far end on the link. auto(4) is used to indicate that the interface is capable and willing to become a trunk but will not initiate trunking negotiations. The far end on the link are required to either start negotiations or start sending encapsulated packets, on which event the specified interface will become a trunk. onNoNegotiate(5) is used to indicate that the interface is permanently set to be a trunk, and no negotiation takes place with the far end on the link to ensure consistent operation. This is similar to on(1) except no negotiation takes place with the far end. If the port does not support negotiation or its vlanTrunkPortEncapsulationType is set to negotiate(5), onNoNegotiate(5) is not allowed. Devices that do no support dynamic determination (for just a particular interface, encapsulation or for the whole device) need only support the 'on', and 'off' values." ::= { vlanTrunkPortEntry 13 } vlanTrunkPortDynamicStatus OBJECT-TYPE SYNTAX INTEGER { trunking(1), notTrunking(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the specified interface is either acting as a trunk or not. This is a result of the vlanTrunkPortDynamicState and the ifOperStatus of the trunk port itself." ::= { vlanTrunkPortEntry 14 } vlanTrunkPortVtpEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Some trunk interface modules allow VTP to be enabled/disabled seperately from that of the central device. In such a case this object provides management a way to remotely enable VTP on that module. If a module does not support a seperate VTP enabled state then this object shall always return 'true' and will accept no other value during a SET operation." ::= { vlanTrunkPortEntry 15 } vlanTrunkPortEncapsulationOperType OBJECT-TYPE SYNTAX INTEGER { isl(1), dot10(2), lane(3), dot1Q(4), negotiating(5), notApplicable(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of VLAN encapsulation in use on this trunk port. For intefaces with vlanTrunkPortDynamicStatus of notTrunking(2) the vlanTrunkPortEncapsulationOperType shall be notApplicable(6)." ::= { vlanTrunkPortEntry 16 } vlanTrunkPortVlansEnabled2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 1024 through 2047 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 1024 through 1031; the second octet to VLANs 1032 through 1039; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local system is enabled for sending and receiving frames on that VLAN; if the bit is set to '0', then the system is disabled from sending and receiving frames on that VLAN. The default value is zero length string. To avoid conflicts between overlapping partial updates by multiple managers, i.e., updates which modify only a portion of an instance of this object (e.g., enable/disable a single VLAN on the trunk port), any SNMP Set operation accessing an instance of this object should also write the value of vlanTrunkPortSetSerialNo." ::= { vlanTrunkPortEntry 17 } vlanTrunkPortVlansEnabled3k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 2048 through 3071 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local system is enabled for sending and receiving frames on that VLAN; if the bit is set to '0', then the system is disabled from sending and receiving frames on that VLAN. The default value is zero length string. To avoid conflicts between overlapping partial updates by multiple managers, i.e., updates which modify only a portion of an instance of this object (e.g., enable/disable a single VLAN on the trunk port), any SNMP Set operation accessing an instance of this object should also write the value of vlanTrunkPortSetSerialNo." ::= { vlanTrunkPortEntry 18 } vlanTrunkPortVlansEnabled4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 3072 through 4095 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 3072 through 3079; the second octet to VLANs 3080 through 3087; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local system is enabled for sending and receiving frames on that VLAN; if the bit is set to '0', then the system is disabled from sending and receiving frames on that VLAN. The default value is zero length string. To avoid conflicts between overlapping partial updates by multiple managers, i.e., updates which modify only a portion of an instance of this object (e.g., enable/disable a single VLAN on the trunk port), any SNMP Set operation accessing an instance of this object should also write the value of vlanTrunkPortSetSerialNo." ::= { vlanTrunkPortEntry 19 } vtpVlansPruningEligible2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 1024 through 2047 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 1024 through 1031; the second octet to VLANs 1032 through 1039; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local system is permitted to prune that VLAN on this trunk port; if the bit is set to '0', then the system must not prune that VLAN on this trunk port. The default value is zero length string. To avoid conflicts between overlapping partial updates by multiple managers, i.e., updates which modify only a portion of an instance of this object (e.g., enable/disable a single VLAN on the trunk port), any SNMP Set operation accessing an instance of this object should also write the value of vlanTrunkPortSetSerialNo." ::= { vlanTrunkPortEntry 20 } vtpVlansPruningEligible3k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 2048 through 3071 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local system is permitted to prune that VLAN on this trunk port; if the bit is set to '0', then the system must not prune that VLAN on this trunk port. The default value is zero length string. To avoid conflicts between overlapping partial updates by multiple managers, i.e., updates which modify only a portion of an instance of this object (e.g., enable/disable a single VLAN on the trunk port), any SNMP Set operation accessing an instance of this object should also write the value of vlanTrunkPortSetSerialNo." ::= { vlanTrunkPortEntry 21 } vtpVlansPruningEligible4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 3072 through 4095 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 3072 through 3079; the second octet to VLANs 3080 through 3087; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local system is permitted to prune that VLAN on this trunk port; if the bit is set to '0', then the system must not prune that VLAN on this trunk port. The default value is zero length string. To avoid conflicts between overlapping partial updates by multiple managers, i.e., updates which modify only a portion of an instance of this object (e.g., enable/disable a single VLAN on the trunk port), any SNMP Set operation accessing an instance of this object should also write the value of vlanTrunkPortSetSerialNo." ::= { vlanTrunkPortEntry 22 } vlanTrunkPortVlansXmitJoined2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 1024 through 2047 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 1024 through 1031; the second octet to VLANs 1032 through 1039; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then this VLAN is presently being forwarded on this trunk port, i.e., it is not pruned; if the bit is set to '0', then this VLAN is presently not being forwarded on this trunk port, either because it is pruned or for some other reason." ::= { vlanTrunkPortEntry 23 } vlanTrunkPortVlansXmitJoined3k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 2048 through 3071 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then this VLAN is presently being forwarded on this trunk port, i.e., it is not pruned; if the bit is set to '0', then this VLAN is presently not being forwarded on this trunk port, either because it is pruned or for some other reason." ::= { vlanTrunkPortEntry 24 } vlanTrunkPortVlansXmitJoined4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 3072 through 4095 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 3072 through 3079; the second octet to VLANs 3080 through 3087; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then this VLAN is presently being forwarded on this trunk port, i.e., it is not pruned; if the bit is set to '0', then this VLAN is presently not being forwarded on this trunk port, either because it is pruned or for some other reason." ::= { vlanTrunkPortEntry 25 } vlanTrunkPortVlansRcvJoined2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 1024 through 2047 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 1024 through 1031; the second octet to VLANs 1032 through 1039; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local switch is currently sending joins for this VLAN on this trunk port, i.e., it is asking to receive frames for this VLAN; if the bit is set to '0', then the local switch is not currently sending joins for this VLAN on this trunk port." ::= { vlanTrunkPortEntry 26 } vlanTrunkPortVlansRcvJoined3k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 2048 through 3071 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local switch is currently sending joins for this VLAN on this trunk port, i.e., it is asking to receive frames for this VLAN; if the bit is set to '0', then the local switch is not currently sending joins for this VLAN on this trunk port." ::= { vlanTrunkPortEntry 27 } vlanTrunkPortVlansRcvJoined4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 3072 through 4095 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 3072 through 3079; the second octet to VLANs 3080 through 3087; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local switch is currently sending joins for this VLAN on this trunk port, i.e., it is asking to receive frames for this VLAN; if the bit is set to '0', then the local switch is not currently sending joins for this VLAN on this trunk port." ::= { vlanTrunkPortEntry 28 } vlanTrunkPortDot1qTunnel OBJECT-TYPE SYNTAX INTEGER { trunk(1), access(2), disabled(3) } MAX-ACCESS read-create STATUS deprecated DESCRIPTION "Indicates dot1qtunnel mode of the port. If the portDot1qTunnel is set to 'trunk' mode, the port's vlanTrunkPortDynamicState will be changed to 'onNoNegotiate' and the vlanTrunkPortEncapsulationType will be set to 'dot1Q'. These values cannot be changed unless dot1q tunnel is disabled on this port. If the portDot1qTunnel mode is set to 'access' mode, the port's vlanTrunkPortDynamicState will be set to 'off'.And the value of vlanTrunkPortDynamicState cannot be changed unless dot1q tunnel is disabled on this port. 1Q packets received on this access port will remain. Setting the port to dot1q tunnel 'disabled' mode causes the dot1q tunnel feature to be disabled on this port. This object can't be set to 'trunk' or 'access' mode, when vlanTrunkPortsDot1qTag object is set to 'false'. This object has been deprecated and is replaced by the object 'cltcDot1qTunnelMode' in the CISCO-L2-TUNNEL-CONFIG-MIB" DEFVAL { disabled } ::= { vlanTrunkPortEntry 29 } vlanTrunkPortVlansActiveFirst2k OBJECT-TYPE SYNTAX Cisco2KVlanList MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN with VlanIndex values of 0 through 2047. If the bit corresponding to a VLAN is set to 1, it indicates that vlan is allowed and active in management domain. If the bit corresponding to a VLAN is set to 0, it indicates that vlan is not allowed or not active in management domain." ::= { vlanTrunkPortEntry 30 } vlanTrunkPortVlansActiveSecond2k OBJECT-TYPE SYNTAX Cisco2KVlanList MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN with VlanIndex values of 2048 through 4095. If the bit corresponding to a VLAN is set to 1, it indicates that vlan is allowed and active in management domain. If the bit corresponding to a VLAN is set to 0, it indicates that vlan is not allowed or not active in management domain." ::= { vlanTrunkPortEntry 31 } vlanTrunkPortSetSerialNo OBJECT-TYPE SYNTAX TestAndIncr MAX-ACCESS read-write STATUS current DESCRIPTION "An advisory lock used to allow several cooperating SNMPv2 managers to coordinate their use of the SNMPv2 set operation acting upon any instance of vlanTrunkPortVlansEnabled." ::= { vlanTrunkPorts 2 } vlanTrunkPortsDot1qTag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS deprecated DESCRIPTION "An indication of whether the tagging on all VLANs including native VLAN for all 802.1q trunks is enabled. If this object has a value of true(1) then all VLANs including native VLAN are tagged. If the value is false(2) then all VLANs excluding native VLAN are tagged. This object has been deprecated and is replaced by the object 'cltcDot1qAllTaggedEnabled' in the CISCO-L2-TUNNEL-CONFIG-MIB" DEFVAL { false } ::= { vlanTrunkPorts 3 } vtpDiscover OBJECT IDENTIFIER ::= { vtpMIBObjects 7 } vtpDiscoverTable OBJECT-TYPE SYNTAX SEQUENCE OF VtpDiscoverEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information related to the discovery of the VTP members in the designated management domain. This table is not instantiated when managementDomainVersionInUse is version1(1), version2(3) or none(3)." ::= { vtpDiscover 1 } vtpDiscoverEntry OBJECT-TYPE SYNTAX VtpDiscoverEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information related to the discovery of the VTP members in one management domain." INDEX { managementDomainIndex } ::= { vtpDiscoverTable 1 } VtpDiscoverEntry ::= SEQUENCE { vtpDiscoverAction INTEGER, vtpDiscoverStatus INTEGER, vtpLastDiscoverTime TimeStamp } vtpDiscoverAction OBJECT-TYPE SYNTAX INTEGER { discover(1), noOperation(2), purgeResult(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "When this object is set to discover(1), all the entries in vtpDiscoverResultTable for the corresponding management domain will be removed and the local device will begin to discover all VTP members in the management domain. Upon the successful completion of discovery, the discovered result will be stored in the vtpDiscoverResultTable. If vtpDiscoverStatus is inProgress(1), setting vtpDiscoverAction to discover(1) will fail. When this object is set to purgeResult(3), all the entries of vtpDiscoverResultTable for the corresponding management domain will be removed from vtpDiscoverResultTable. When this object is set to noOperation(2), no action will be taken. When read, this object always returns noOperation(2)." ::= { vtpDiscoverEntry 1 } vtpDiscoverStatus OBJECT-TYPE SYNTAX INTEGER { inProgress(1), succeeded(2), resourceUnavailable(3), someOtherError(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current status of VTP discovery. inProgress - a discovery is in progress; succeeded - the discovery was completed successfully (this value is also used when no discover has been invoked since the last time the local system restarted); resourceUnavailable - the discovery failed because the required allocation of a resource is presently unavailable. someOtherError - 'the discovery failed due to a reason no listed." ::= { vtpDiscoverEntry 2 } vtpLastDiscoverTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at which the last discovery was completed. A value of zero indicates that no discovery has been invoked since last time the local system restarted." ::= { vtpDiscoverEntry 3 } vtpDiscoverResultTable OBJECT-TYPE SYNTAX SEQUENCE OF VtpDiscoverResultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table containing information of discovered VTP members in the management domain in which the local system is participating. This table is not instantiated when managementDomainVersionInUse is version1(1), version2(2) or none(3)." ::= { vtpDiscover 2 } vtpDiscoverResultEntry OBJECT-TYPE SYNTAX VtpDiscoverResultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row is created for each VTP member which is found through successful discovery." INDEX { managementDomainIndex, vtpDiscoverResultIndex } ::= { vtpDiscoverResultTable 1 } VtpDiscoverResultEntry ::= SEQUENCE { vtpDiscoverResultIndex Unsigned32, vtpDiscoverResultDatabaseName SnmpAdminString, vtpDiscoverResultConflicting TruthValue, vtpDiscoverResultDeviceId SnmpAdminString, vtpDiscoverResultPrimaryServer SnmpAdminString, vtpDiscoverResultRevNumber Gauge32, vtpDiscoverResultSystemName SnmpAdminString } vtpDiscoverResultIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "A value assigned by the system which identifies a VTP member and the associated database in the management domain." ::= { vtpDiscoverResultEntry 1 } vtpDiscoverResultDatabaseName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The database name associated with the discovered VTP member." ::= { vtpDiscoverResultEntry 2 } vtpDiscoverResultConflicting OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether this VTP member contains conflicting information. true(1) indicates that this member has conflicting information of the database type in the management domain. false(2) indicates that there is no conflicting information of the database type in the management domain." ::= { vtpDiscoverResultEntry 3 } vtpDiscoverResultDeviceId OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The unique identifier of the device for this VTP member." ::= { vtpDiscoverResultEntry 4 } vtpDiscoverResultPrimaryServer OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The unique identifier of the primary server for this VTP member and the associated database type. There are two different VTP servers, the primary server and the secondary server. When a local device is configured as a server for a certain database type, it becomes secondary server by default. Primary server is an operational role under which a server can initiate or change the VTP configuration of the database type. If this VTP member itself is the primary server, the value of this object is the same as the value of vtpDiscoverResultDeviceId of the instance." ::= { vtpDiscoverResultEntry 5 } vtpDiscoverResultRevNumber OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current configuration revision number as known by the VTP member. When the database type is unknown for the VTP member, this value is 0." ::= { vtpDiscoverResultEntry 6 } vtpDiscoverResultSystemName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "sysName of the VTP member." ::= { vtpDiscoverResultEntry 7 } vtpDatabase OBJECT IDENTIFIER ::= { vtpMIBObjects 8 } vtpDatabaseTable OBJECT-TYPE SYNTAX SEQUENCE OF VtpDatabaseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information of the VTP databases. It is not instantiated when managementDomainVersionInUse is version1(1), version2(3) or none(3)." ::= { vtpDatabase 1 } vtpDatabaseEntry OBJECT-TYPE SYNTAX VtpDatabaseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about the status of the VTP database in the domain. Each VTP database type known to the local device type has an entry in this table. An entry is also created for unknown database which is notified through VTP advertisements from other VTP servers." INDEX { managementDomainIndex, vtpDatabaseIndex } ::= { vtpDatabaseTable 1 } VtpDatabaseEntry ::= SEQUENCE { vtpDatabaseIndex Unsigned32, vtpDatabaseName SnmpAdminString, vtpDatabaseLocalMode INTEGER, vtpDatabaseRevNumber Gauge32, vtpDatabasePrimaryServer TruthValue, vtpDatabasePrimaryServerId SnmpAdminString, vtpDatabaseTakeOverPrimary TruthValue, vtpDatabaseTakeOverPassword SnmpAdminString } vtpDatabaseIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "A value assigned by the system which uniquely identifies a VTP database in the local system." ::= { vtpDatabaseEntry 1 } vtpDatabaseName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the database." ::= { vtpDatabaseEntry 2 } vtpDatabaseLocalMode OBJECT-TYPE SYNTAX INTEGER { client(1), server(2), transparent(3), off(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The local VTP mode for a particular database type in this administrative domain. - 'client' indicates that the local system is acting as a VTP client of the database type. - 'server' indicates that the local system is acting as a VTP server of the database type. - 'transparent' indicates that the local system does not generate or listen to VTP messages of this database type, but forwards messages. This mode can also be set by the device itself when the size of database is too large for it to hold in DRAM. - 'off' indicates that the local system does not generate, listen to or forward any VTP messages of this database type. The default mode is 'client' for the database type known to the local device and 'transparent' for the unknown database type." ::= { vtpDatabaseEntry 3 } vtpDatabaseRevNumber OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current configuration revision number as known by the local device for this VTP 3 database type in the management domain. This value is updated (if necessary) whenever a VTP advertisement for the database type is received or generated. When the database type is unknown to the local device or no VTP advertisement for the database type is received or generated, its value is 0." ::= { vtpDatabaseEntry 4 } vtpDatabasePrimaryServer OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "There are two kinds of VTP version 3 servers for a certain database type - the primary server and the secondary server. When a local device is configured as a server for a certain database type, it becomes secondary server by default. Primary server is an operational role under which a server can initiate or change the VTP configuration of the database type. A true(1) value indicates that the local device is the primary server of the database type in the management domain. A false(2) value indicates that the local device is not the primary server, or the database type is unknown to the local device." ::= { vtpDatabaseEntry 5 } vtpDatabasePrimaryServerId OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The unique identifier of the primary server in the management domain for the database type. If no primary server is discovered for the database type, the object has a value of zero length string." ::= { vtpDatabaseEntry 6 } vtpDatabaseTakeOverPrimary OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "There are two kinds of VTP version 3 servers for a certain database type - the primary server and the secondary server. When a local device is configured as a server for a certain database type, it becomes secondary server by default. Primary server is an operational role under which a server can initiate or change the VTP configuration of the database type. Setting this object to a true(1) value will advertise the configuration of this database type to the whole domain. In order to successfully setting this object to true(1), the value of vtpDatabaseLocalMode must be server(2). Besides that, when the VTP password is hidden from the configuration file, the password (vtpDatabaseTakeOverPassword) which matches the secret key (vtpAuthSecretKey) must be provided in the same data packet. When read, the object always returns false(2)." ::= { vtpDatabaseEntry 7 } vtpDatabaseTakeOverPassword OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "When read, this object always returns the value of a zero-length octet string. In the case that the VTP password is hidden from the configuration and the local device intends to take over the whole domain, this object must be set to the matching password with the secret key (vtpAuthSecretKey) in the same data packet as which the vtpDatabaseTakeOverPrimary is in. In all the other situations, setting a valid value to this object has no impact on the system." ::= { vtpDatabaseEntry 8 } vtpAuthentication OBJECT IDENTIFIER ::= { vtpMIBObjects 9 } vtpAuthenticationTable OBJECT-TYPE SYNTAX SEQUENCE OF VtpAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains the authentication information of VTP in which the local system participates. The security mechanism of VTP relies on a secret key that is used to alter the MD5 digest of the packets transmitted on the wire. The secret value is created from a password that may be saved in plain text in the configuration or hidden from the configuration. The device creating or modifying the VTP configuration signs it using the MD5 digest generated from the secret key before advertising it. Other devices in the domain receive this configuration use the same secret key to accept it if correctly signed or drop it otherwise. The user has the option to hide the password from the configuration. Once the password is hidden, the secret key generated from the password is shown in the configuration instead, and there is no other way to show the password in plain text again but clearing it or resetting it. In an un-trusted area, the password on a device can be configured without being unveiled. After that, it has to be provided again by setting the same value to vtpDatabaseTakeOverPassword if the user wants to take over the whole VTP management domain of the database type. When managementDomainVersionInUse is version3(4), the authentication mechanism is common to all VTP database type." ::= { vtpAuthentication 1 } vtpAuthEntry OBJECT-TYPE SYNTAX VtpAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about the status of the VTP authentication information in one domain." INDEX { managementDomainIndex } ::= { vtpAuthenticationTable 1 } VtpAuthEntry ::= SEQUENCE { vtpAuthPassword SnmpAdminString, vtpAuthPasswordType INTEGER, vtpAuthSecretKey OCTET STRING } vtpAuthPassword OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "By default, this object has a value of a zero-length character string and is considered to be not configured. The device uses the password to generate the secret key. It can be stored in the configuration in plain text or hidden from the configuration. If a VTP server intends to modify the database's configuration in the domain but the password was hidden from the configuration, the same password (vtpDatabaseTakeOverPassword) as the hidden one has to be provided. When this object is set alone, vtpAuthPasswordType is set to plaintext(1) automatically by the system. Setting this object to a zero length character string resets the password to its default value and the password is considered as not configured. This object is not allowed to be set at the same time when vtpAuthSecretKey is set. When the vtpAuthPasswordType is hidden(2), this object will return a zero-length character string when read." ::= { vtpAuthEntry 1 } vtpAuthPasswordType OBJECT-TYPE SYNTAX INTEGER { plaintext(1), hidden(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "By default this object has the value as plaintext(1) and the VTP password is stored in the configuration file in plain text. Setting this object to hidden(2) will hide the password from the configuration. Once this object is set to hidden(2), it cannot be set to plaintext(1) alone. However, it may be set to plaintext(1) at the same time the password is set." ::= { vtpAuthEntry 2 } vtpAuthSecretKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0 | 16)) MAX-ACCESS read-write STATUS current DESCRIPTION "The device creating or modifying the VTP configuration signs it using the MD5 digest generated from the secret key before advertising it. Other devices in the domain receiving this configuration use the same secret key to accept it if it was correctly signed or drop it otherwise. By default, the object has the value as a zero-length string and this value is read only. It is set to this value automatically when the password (vtpAuthPassword) is set to a zero-length octet string. The secret key can be either generated using the password or configured by the user. Once the secret key is configured by the user, it is stored as a hexadecimal string in the device's configuration and the password is considered to be the secret key's matching password and hidden from the configuration automatically. This object is not allowed to be set at the same time when vtpAuthPassword is set. The secret key is overwritten by a newly generated secret key when the password is re-configured." ::= { vtpAuthEntry 3 } vlanStatistics OBJECT IDENTIFIER ::= { vtpMIBObjects 10 } vlanStatsVlans OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of the existing manageable VLANs with VLAN indices from 1 to 1024 in the system." ::= { vlanStatistics 1 } vlanStatsExtendedVlans OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of the existing manageable VLANs with VLAN indices greater than 1024 in the system." ::= { vlanStatistics 2 } vlanStatsInternalVlans OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of the internal VLANs existing in the system." ::= { vlanStatistics 3 } vlanStatsFreeVlans OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of the free or unused VLANs in the system." ::= { vlanStatistics 4 } -- VTP notifications vtpNotifications OBJECT IDENTIFIER ::= { ciscoVtpMIB 2 } vtpNotificationsPrefix OBJECT IDENTIFIER ::= { vtpNotifications 0 } vtpNotificationsObjects OBJECT IDENTIFIER ::= { vtpNotifications 1 } vtpConfigRevNumberError NOTIFICATION-TYPE OBJECTS { managementDomainConfigRevNumber } STATUS current DESCRIPTION "A configuration revision number error notification signifies that a device has incremented its vtpConfigRevNumberErrors counter. Generation of this notification is suppressed if the vtpNotificationsEnabled has the value 'false'. The device must throttle the generation of consecutive vtpConfigRevNumberError notifications so that there is at least a five-second gap between notification of this type. When notification are throttled, they are dropped, not queued for sending at a future time. (Note that 'generating' a notification means sending to all configured recipients.)" ::= { vtpNotificationsPrefix 1 } vtpConfigDigestError NOTIFICATION-TYPE OBJECTS { managementDomainConfigRevNumber } STATUS current DESCRIPTION "A configuration digest error notification signifies that a device has incremented its vtpConfigDigestErrors counter. Generation of this notification is suppressed if the vtpNotificationsEnabled has the value 'false'. The device must throttle the generation of consecutive vtpConfigDigestError notifications so that there is at least a five-second gap between notification of this type. When notification are throttled, they are dropped, not queued for sending at a future time. (Note that 'generating' a notification means sending to all configured recipients.)" ::= { vtpNotificationsPrefix 2 } vtpServerDisabled NOTIFICATION-TYPE OBJECTS { managementDomainConfigRevNumber, vtpMaxVlanStorage } STATUS current DESCRIPTION "A VTP Server disabled notification is generated when the local system is no longer able to function as a VTP Server because the number of defined VLANs is greater than vtpMaxVlanStorage or the local system is not able to recover complete VTP information after a reboot. Generation of this notification is suppressed if the vtpNotificationsEnabled has the value 'false'." ::= { vtpNotificationsPrefix 3 } vtpMtuTooBig NOTIFICATION-TYPE OBJECTS { vlanTrunkPortManagementDomain, vtpVlanState } STATUS current DESCRIPTION "A VTP MTU tooBig notification is generated when a VLAN's MTU size is larger than can be supported either: - by one or more of its trunk ports: the included vtpVlanState has the value 'mtuTooBigForTrunk' and the included vlanTrunkPortManagementDomain is for the first (or only) trunk port, or - by the device itself: vtpVlanState has the value 'mtuTooBigForDevice' and any instance of vlanTrunkPortManagementDomain is included. Devices which have no trunk ports do not send vtpMtuTooBig notifications. Generation of this notification is suppressed if the vtpNotificationsEnabled has the value 'false'." ::= { vtpNotificationsPrefix 4 } vtpVersionOneDeviceDetected NOTIFICATION-TYPE OBJECTS { vlanTrunkPortManagementDomain } STATUS current DESCRIPTION "A VTP version one device detected notification is generated by a device when: a) a management domain has been put into version 2 mode (as accessed by managementDomainVersionInUse). b) 15 minutes has passed since a). c) a version 1 PDU is detected on a trunk on the device that is in that management domain which has a lower revision number than the current configuration." ::= { vtpNotificationsPrefix 6 } vlanTrunkPortDynamicStatusChange NOTIFICATION-TYPE OBJECTS { vlanTrunkPortDynamicStatus } STATUS current DESCRIPTION "A vlanTrunkPortDynamicStatusChange notification is generated by a device when the value of vlanTrunkPortDynamicStatus object has been changed." ::= { vtpNotificationsPrefix 7 } vtpLocalModeChanged NOTIFICATION-TYPE OBJECTS { managementDomainLocalMode } STATUS current DESCRIPTION "A vtpLocalModeChanged notification is generated by a device when the value of the object managementDomainLocalMode is changed." ::= { vtpNotificationsPrefix 8 } vtpVersionInUseChanged NOTIFICATION-TYPE OBJECTS { managementDomainVersionInUse } STATUS current DESCRIPTION "A vtpVersionInUseChanged notification is generated by a device when the value of the object managementDomainVersionInUse is changed." ::= { vtpNotificationsPrefix 9 } vtpVlanCreated NOTIFICATION-TYPE OBJECTS { vtpVlanName } STATUS current DESCRIPTION "A vtpVlanCreated notification is generated by a device when a VLAN is created." ::= { vtpNotificationsPrefix 10 } vtpVlanDeleted NOTIFICATION-TYPE OBJECTS { vtpVlanName } STATUS current DESCRIPTION "A vtpVlanDeleted notification is generated by a device when a VLAN is deleted." ::= { vtpNotificationsPrefix 11 } vtpVlanRingNumberConflict NOTIFICATION-TYPE OBJECTS { vtpVlanRingNumber, ifIndex, vtpVlanPortLocalSegment } STATUS current DESCRIPTION "A VTP ring number configuration conflict notification is generated if, and only at the time when, a device learns of a conflict between: a) the ring number (vtpVlanPortLocalSegment) being used on a token ring segment attached to the port identified by ifIndex, and b) the VTP-obtained ring number (vtpVlanRingNumber) for the VLAN identified by vtpVlanIndex. When such a conflict occurs, the bridge port is put into an administrative down position until the conflict is resolved through local/network management intervention. This notification is only applicable to VLANs of type 'tokenRing'." ::= { vtpNotificationsPrefix 12 } vtpPruningStateOperChange NOTIFICATION-TYPE OBJECTS { managementDomainPruningStateOper } STATUS current DESCRIPTION "A vtpPruningStateOperChange notification is generated by the device when the instance value of managementDomainPruningStateOper is changed." ::= { vtpNotificationsPrefix 13 } vtpVlanPortLocalSegment OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The ring (segment) number in use on a 802.5 ring. For bridges supporting RFC 1525, this value is the same as given by dot1dSrPortLocalSegment for the bridge port attached to that ring. When tokenRing VLANs are in use, each 'trNet' VLAN can/does have a different instance of dot1dSrPortLocalSegment for each physical port. Note that access to the particuler instance of dot1dSrPortLocalSegment requires knowledge of how the agent supports the multiple 'contexts' required to implement RFC 1525 for multiple VLANs; also note that the assignment of ifIndex values may be different in different 'contexts'." ::= { vtpNotificationsObjects 1 } -- Conformance Information vtpMIBConformance OBJECT IDENTIFIER ::= { ciscoVtpMIB 3 } vtpMIBCompliances OBJECT IDENTIFIER ::= { vtpMIBConformance 1 } vtpMIBGroups OBJECT IDENTIFIER ::= { vtpMIBConformance 2 } -- compliance statements vtpMIBCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for VTP implementations." MODULE -- this module MANDATORY-GROUPS { vtpBasicGroup, vtpVlanInfoGroup, vtpStatsGroup, vtpTrunkPortGroup } GROUP vtpVlanInfoEditGroup DESCRIPTION "This group must be implemented by VTP Servers. VTP Clients need not implement these objects, and must not allow VLANs to be created, modified, or destroyed using these objects." OBJECT managementDomainRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortManagementDomain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortNativeVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { vtpMIBCompliances 1 } vtpMIBCompliance2 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for VTP implementations." MODULE -- this module MANDATORY-GROUPS { vtpBasicGroup, vtpVlanInfoGroup, vtpStatsGroup, vtpTrunkPortGroup } GROUP vtpVlanInfoEditGroup DESCRIPTION "This group must be implemented by VTP Servers. VTP Clients need not implement these objects, and must not allow VLANs to be created, modified, or destroyed using these objects." GROUP vtp4kVlanGroup DESCRIPTION "This group must be implemented by the VTP Servers which support the range of VlanIndex between 1024 and 4095." OBJECT managementDomainRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortManagementDomain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortNativeVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { vtpMIBCompliances 2 } vtpMIBCompliance3 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for VTP implementations." MODULE -- this module MANDATORY-GROUPS { vtpBasicGroup, vtpVlanInfoGroup, vtpStatsGroup, vtpTrunkPortGroup } GROUP vtpVlanInfoEditGroup DESCRIPTION "This group must be implemented by VTP Servers. VTP Clients need not implement these objects, and must not allow VLANs to be created, modified, or destroyed using these objects." GROUP vtp4kVlanGroup DESCRIPTION "This group must be implemented by the VTP Servers which support the range of VlanIndex between 1024 and 4095." GROUP vtpDot1qTunnelGroup DESCRIPTION "This group is mandatory for all the ports which implement dot1qtunnel feature." OBJECT managementDomainRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortManagementDomain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortNativeVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortDot1qTunnel MIN-ACCESS read-only DESCRIPTION "This object is read-only for interface which doesn't support dot1q tunnel feature." ::= { vtpMIBCompliances 3 } vtpMIBCompliance4 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for VTP implementations." MODULE -- this module MANDATORY-GROUPS { vtpBasicGroup, vtpVlanInfoGroup, vtpStatsGroup, vtpTrunkPortGroup } GROUP vtpVlanInfoEditGroup DESCRIPTION "This group must be implemented by VTP Servers. VTP Clients need not implement these objects, and must not allow VLANs to be created, modified, or destroyed using these objects." GROUP vtp4kVlanGroup DESCRIPTION "This group must be implemented by the VTP Servers which support the range of VlanIndex between 1024 and 4095." GROUP vtpDot1qTunnelGroup DESCRIPTION "This group is mandatory for all the ports which implement dot1qtunnel feature." GROUP vtpVlanIfIndexGroup DESCRIPTION "This group is an optional group containing objects providing information about the mapping of VLAN ID to its corresponding IfIndex." OBJECT managementDomainRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortManagementDomain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortNativeVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortDot1qTunnel MIN-ACCESS read-only DESCRIPTION "This object is read-only for interface which doesn't support dot1q tunnel feature." ::= { vtpMIBCompliances 4 } vtpMIBCompliance5 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for VTP implementations." MODULE -- this module MANDATORY-GROUPS { vtpBasicGroup, vtpVlanInfoGroup, vtpStatsGroup, vtpTrunkPortGroup, vtpVersion2BasicGroup } GROUP vtpVlanInfoEditGroup DESCRIPTION "This group must be implemented by VTP Servers. VTP Clients need not implement these objects, and must not allow VLANs to be created, modified, or destroyed using these objects." GROUP vtp4kVlanGroup DESCRIPTION "This group must be implemented by the VTP Servers which support the range of VlanIndex between 1024 and 4095." GROUP vtpDot1qTunnelGroup DESCRIPTION "This group is mandatory for all the ports which implement dot1qtunnel feature." GROUP vtpVlanIfIndexGroup DESCRIPTION "This group is an optional group containing objects providing information about the mapping of VLAN ID to its corresponding IfIndex." GROUP vtpVlanInfoEditGroup2 DESCRIPTION "This group is mandatory for devices which only support one VLAN editing for each 'apply' operation." OBJECT managementDomainRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT managementDomainName MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainLocalMode MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainTftpServer MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainTftpPathname MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainVersionInUse MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT vlanTrunkPortManagementDomain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortNativeVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortDot1qTunnel MIN-ACCESS read-only DESCRIPTION "This object is read-only for interface which doesn't support dot1q tunnel feature." ::= { vtpMIBCompliances 5 } vtpMIBCompliance6 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for VTP implementations." MODULE -- this module MANDATORY-GROUPS { vtpBasicGroup, vtpVlanInfoGroup, vtpConfigNotificationsGroup, vtpStatsGroup, vtpTrunkPortGroup, vtpVersion2BasicGroup, vtpNotificationObjectsGroup } GROUP vtpVlanInfoEditGroup DESCRIPTION "This group must be implemented by VTP Servers. VTP Clients need not implement these objects, and must not allow VLANs to be created, modified, or destroyed using these objects." GROUP vtp4kVlanGroupRev1 DESCRIPTION "This group must be implemented by the VTP Servers which support the range of VlanIndex between 1024 and 4095." GROUP vtpDot1qTunnelGroup DESCRIPTION "This group is mandatory for all the ports which implement dot1qtunnel feature." GROUP vtpVlanIfIndexGroup DESCRIPTION "This group is an optional group containing objects providing information about the mapping of VLAN ID to its corresponding IfIndex." GROUP vtpVlanInfoEditGroup2 DESCRIPTION "This group is mandatory for devices which only support one VLAN editing for each 'apply' operation." OBJECT managementDomainRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT managementDomainName MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainLocalMode MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainTftpServer MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainTftpPathname MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainVersionInUse MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT vlanTrunkPortManagementDomain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortNativeVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditTypeExt2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortDot1qTunnel MIN-ACCESS read-only DESCRIPTION "This object is read-only for interface which doesn't support dot1q tunnel feature." ::= { vtpMIBCompliances 6 } vtpMIBCompliance7 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for VTP implementations." MODULE -- this module MANDATORY-GROUPS { vtpBasicGroup, vtpVlanInfoGroup, vtpConfigNotificationsGroup, vtpStatsGroup, vtpTrunkPortGroup, vtpVersion2BasicGroup, vtpNotificationObjectsGroup } GROUP vtpVlanInfoEditGroup DESCRIPTION "This group must be implemented by VTP Servers. VTP Clients need not implement these objects, and must not allow VLANs to be created, modified, or destroyed using these objects." GROUP vtp4kVlanGroupRev1 DESCRIPTION "This group must be implemented by the VTP Servers which support the range of VlanIndex between 1024 and 4095." GROUP vtpDot1qTunnelGroup DESCRIPTION "This group is mandatory for all the ports which implement dot1qtunnel feature." GROUP vtpVlanIfIndexGroup DESCRIPTION "This group is an optional group containing objects providing information about the mapping of VLAN ID to its corresponding IfIndex." GROUP vtpVlanInfoEditGroup2 DESCRIPTION "This group is mandatory for devices which only support one VLAN editing for each 'apply' operation." OBJECT managementDomainRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT managementDomainName MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainLocalMode SYNTAX INTEGER { client(1), server(2), transparent(3) } MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3). Write access for transparent(3) is not required." OBJECT managementDomainTftpServer MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainTftpPathname MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainVersionInUse MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT vlanTrunkPortManagementDomain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortNativeVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditTypeExt2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortDot1qTunnel MIN-ACCESS read-only DESCRIPTION "This object is read-only for interface which doesn't support dot1q tunnel feature." ::= { vtpMIBCompliances 7 } vtpMIBCompliance8 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for VTP implementations." MODULE -- this module MANDATORY-GROUPS { vtpBasicGroup, vtpVlanInfoGroup, vtpConfigNotificationsGroup, vtpStatsGroup, vtpTrunkPortGroup, vtpVersion2BasicGroup, vtpNotificationObjectsGroup } GROUP vtpVlanInfoEditGroup DESCRIPTION "This group must be implemented by VTP Servers. VTP Clients need not implement these objects, and must not allow VLANs to be created, modified, or destroyed using these objects." GROUP vtp4kVlanGroupRev1 DESCRIPTION "This group must be implemented by the VTP Servers which support the range of VlanIndex between 1024 and 4095." GROUP vtpDot1qTunnelGroup2 DESCRIPTION "This group is mandatory for all the ports which implement dot1qtunnel feature." GROUP vtpVlanIfIndexGroup DESCRIPTION "This group is an optional group containing objects providing information about the mapping of VLAN ID to its corresponding IfIndex." GROUP vtpVlanInfoEditGroup2 DESCRIPTION "This group is mandatory for devices which only support one VLAN editing for each 'apply' operation." OBJECT managementDomainRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT managementDomainName MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainLocalMode SYNTAX INTEGER { client(1), server(2), transparent(3) } MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3). Write access for transparent(3) is not required." OBJECT managementDomainTftpServer MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainTftpPathname MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainVersionInUse MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT vlanTrunkPortManagementDomain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortNativeVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditTypeExt2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { vtpMIBCompliances 8 } vtpMIBCompliance9 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for VTP implementations." MODULE -- this module MANDATORY-GROUPS { vtpBasicGroup, vtpVlanInfoGroup, vtpConfigNotificationsGroup, vtpStatsGroup, vtpTrunkPortGroup, vtpVersion2BasicGroup, vtpNotificationObjectsGroup } GROUP vtpVlanInfoEditGroup DESCRIPTION "This group must be implemented by VTP Servers. VTP Clients need not implement these objects, and must not allow VLANs to be created, modified, or destroyed using these objects." GROUP vtp4kVlanGroupRev1 DESCRIPTION "This group must be implemented by the VTP Servers which support the range of VlanIndex between 1024 and 4095." GROUP vtpVlanIfIndexGroup DESCRIPTION "This group is an optional group containing objects providing information about the mapping of VLAN ID to its corresponding IfIndex." GROUP vtpVlanInfoEditGroup2 DESCRIPTION "This group is mandatory for devices which only support one VLAN editing for each 'apply' operation." GROUP vtpVlanNotifEnabledGroup DESCRIPTION "This group is mandatory for devices which support the notifications/traps in vtpConfigNotificationsGroup3." OBJECT managementDomainRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT managementDomainName MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainLocalMode SYNTAX INTEGER { client(1), server(2), transparent(3) } MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3). Write access for transparent(3) is not required." OBJECT managementDomainTftpServer MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainTftpPathname MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainVersionInUse MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT vlanTrunkPortManagementDomain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortNativeVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditTypeExt2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { vtpMIBCompliances 9 } vtpMIBCompliance10 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for VTP implementations." MODULE -- this module MANDATORY-GROUPS { vtpBasicGroup, vtpVlanInfoGroup, vtpConfigNotificationsGroup, vtpStatsGroup, vtpTrunkPortGroup, vtpVersion2BasicGroup, vtpNotificationObjectsGroup } GROUP vtpVlanInfoEditGroup DESCRIPTION "This group must be implemented by VTP Servers. VTP Clients need not implement these objects, and must not allow VLANs to be created, modified, or destroyed using these objects." GROUP vtp4kVlanGroupRev1 DESCRIPTION "This group must be implemented by the VTP Servers which support the range of VlanIndex between 1024 and 4095." GROUP vtpVlanIfIndexGroup DESCRIPTION "This group is an optional group containing objects providing information about the mapping of VLAN ID to its corresponding IfIndex." GROUP vtpVlanInfoEditGroup2 DESCRIPTION "This group is mandatory for devices which only support one VLAN editing for each 'apply' operation." GROUP vtpVlanNotifEnabledGroup DESCRIPTION "This group is mandatory for devices which support the notifications/traps in vtpConfigNotificationsGroup3." GROUP vtpDiscoverGroup DESCRIPTION "This group is mandatory for devices which support the VTP discovery." GROUP vtpDatabaseGroup DESCRIPTION "This group is mandatory for devices which support the VTP distribution of different database types." GROUP vtpAuthGroup DESCRIPTION "This group is mandatory for devices which support asymmetric keys authentication mechanism for VTP." OBJECT managementDomainRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT managementDomainName MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainLocalMode SYNTAX INTEGER { client(1), server(2), transparent(3) } MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainTftpServer MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainTftpPathname MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainVersionInUse MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT vlanTrunkPortManagementDomain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortNativeVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditTypeExt2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { vtpMIBCompliances 10 } vtpMIBCompliance11 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for VTP implementations." MODULE -- this module MANDATORY-GROUPS { vtpBasicGroup, vtpVlanInfoGroup, vtpConfigNotificationsGroupRev1, vtpStatsGroup, vtpTrunkPortGroup, vtpVersion2BasicGroup, vtpNotificationObjectsGroup } GROUP vtpVlanInfoEditGroup DESCRIPTION "This group must be implemented by VTP Servers. VTP Clients need not implement these objects, and must not allow VLANs to be created, modified, or destroyed using these objects." GROUP vtp4kVlanGroupRev1 DESCRIPTION "This group must be implemented by the VTP Servers which support the range of VlanIndex between 1024 and 4095." GROUP vtpVlanIfIndexGroup DESCRIPTION "This group is an optional group containing objects providing information about the mapping of VLAN ID to its corresponding IfIndex." GROUP vtpVlanInfoEditGroup2 DESCRIPTION "This group is mandatory for devices which only support one VLAN editing for each 'apply' operation." GROUP vtpVlanNotifEnabledGroup DESCRIPTION "This group is mandatory for devices which support the notifications/traps in vtpConfigNotificationsGroup3." GROUP vtpDiscoverGroup DESCRIPTION "This group is mandatory for devices which support the VTP discovery." GROUP vtpDatabaseGroup DESCRIPTION "This group is mandatory for devices which support the VTP distribution of different database types." GROUP vtpAuthGroup DESCRIPTION "This group is mandatory for devices which support asymmetric keys authentication mechanism for VTP." OBJECT managementDomainRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT managementDomainName MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainLocalMode SYNTAX INTEGER { client(1), server(2), transparent(3) } MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainTftpServer MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainTftpPathname MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainVersionInUse MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT vlanTrunkPortManagementDomain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortNativeVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditTypeExt2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { vtpMIBCompliances 11 } vtpMIBCompliance12 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for VTP implementations." MODULE -- this module MANDATORY-GROUPS { vtpBasicGroup, vtpVlanInfoGroup, vtpConfigNotificationsGroupRev1, vtpStatsGroup, vtpTrunkPortGroup, vtpVersion2BasicGroup, vtpNotificationObjectsGroup } GROUP vtpVlanInfoEditGroup DESCRIPTION "This group must be implemented by VTP Servers. VTP Clients need not implement these objects, and must not allow VLANs to be created, modified, or destroyed using these objects." GROUP vtp4kVlanGroupRev1 DESCRIPTION "This group must be implemented by the VTP Servers which support the range of VlanIndex between 1024 and 4095." GROUP vtpVlanIfIndexGroup DESCRIPTION "This group is an optional group containing objects providing information about the mapping of VLAN ID to its corresponding IfIndex." GROUP vtpVlanInfoEditGroup2 DESCRIPTION "This group is mandatory for devices which only support one VLAN editing for each 'apply' operation." GROUP vtpVlanNotifEnabledGroup DESCRIPTION "This group is mandatory for devices which support the notifications/traps in vtpConfigNotificationsGroup3." GROUP vtpDiscoverGroup DESCRIPTION "This group is mandatory for devices which support the VTP discovery." GROUP vtpDatabaseGroup DESCRIPTION "This group is mandatory for devices which support the VTP distribution of different database types." GROUP vtpAuthGroup DESCRIPTION "This group is mandatory for devices which support asymmetric keys authentication mechanism for VTP." GROUP vtpInternalVlanGrp DESCRIPTION "Implementation of this group is optional." OBJECT managementDomainRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT managementDomainName MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainLocalMode SYNTAX INTEGER { client(1), server(2), transparent(3) } MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainTftpServer MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainTftpPathname MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainVersionInUse MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT vlanTrunkPortManagementDomain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortNativeVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditTypeExt2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { vtpMIBCompliances 12 } vtpMIBCompliance13 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for VTP implementations." MODULE -- this module MANDATORY-GROUPS { vtpBasicGroup, vtpVlanInfoGroup, vtpConfigNotificationsGroupRev1, vtpStatsGroup, vtpTrunkPortGroup, vtpVersion2BasicGroup, vtpNotificationObjectsGroup } GROUP vtpVlanInfoEditGroup DESCRIPTION "This group must be implemented by VTP Servers. VTP Clients need not implement these objects, and must not allow VLANs to be created, modified, or destroyed using these objects." GROUP vtp4kVlanGroupRev1 DESCRIPTION "This group must be implemented by the VTP Servers which support the range of VlanIndex between 1024 and 4095." GROUP vtpVlanIfIndexGroup DESCRIPTION "This group is an optional group containing objects providing information about the mapping of VLAN ID to its corresponding IfIndex." GROUP vtpVlanInfoEditGroup2 DESCRIPTION "This group is mandatory for devices which only support one VLAN editing for each 'apply' operation." GROUP vtpVlanNotifEnabledGroup DESCRIPTION "This group is mandatory for devices which support the notifications/traps in vtpConfigNotificationsGroup3." GROUP vtpDiscoverGroup DESCRIPTION "This group is mandatory for devices which support the VTP discovery." GROUP vtpDatabaseGroup DESCRIPTION "This group is mandatory for devices which support the VTP distribution of different database types." GROUP vtpAuthGroup DESCRIPTION "This group is mandatory for devices which support asymmetric keys authentication mechanism for VTP." GROUP vtpInternalVlanGrp DESCRIPTION "Implementation of this group is optional." GROUP vlanStatsGroup DESCRIPTION "This group is mandatory for agents capable of providing VLAN statistics information." GROUP vtpConfigNotificationsGroup6 DESCRIPTION "Implementation of this group is optional." GROUP vtpConfigNotificationsGroup7 DESCRIPTION "Implementation of this group is optional." OBJECT managementDomainRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT managementDomainName MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainLocalMode SYNTAX INTEGER { client(1), server(2), transparent(3) } MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainTftpServer MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainTftpPathname MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT managementDomainVersionInUse MIN-ACCESS read-only DESCRIPTION "This object is read-only if vtpVersion is none(3)." OBJECT vlanTrunkPortManagementDomain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortNativeVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditTypeExt2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { vtpMIBCompliances 13 } vtpMIBCompliance14 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for VTP implementations." MODULE -- this module MANDATORY-GROUPS { vtpBasicGroup, vtpVlanInfoGroup, vtpConfigNotificationsGroupRev1, vtpStatsGroup, vtpTrunkPortGroup, vtpVersion2BasicGroup, vtpNotificationObjectsGroup } GROUP vtpTrunkPruningGroup DESCRIPTION "Implementation of this group is optional." GROUP vtpTrunkPruningGroup2 DESCRIPTION "Implementation of this group is optional." GROUP vtpTrunkPortGroup2 DESCRIPTION "Implementation of this group is optional." GROUP vtpVlanInfoEditGroup DESCRIPTION "This group must be implemented by VTP Servers. VTP Clients need not implement these objects, and must not allow VLANs to be created, modified, or destroyed using these objects." GROUP vtpTrunkPortGroup3 DESCRIPTION "Implementation of this group is optional." GROUP vtp4kVlanGroupRev1 DESCRIPTION "This group must be implemented by the VTP Servers which support the range of VlanIndex between 1024 and 4095." GROUP vtpVlanIfIndexGroup DESCRIPTION "This group is an optional group containing objects providing information about the mapping of VLAN ID to its corresponding IfIndex." GROUP vtpVlanInfoEditGroup2 DESCRIPTION "This group is mandatory for devices which only support one VLAN editing for each 'apply' operation." GROUP vtpVlanNotifEnabledGroup DESCRIPTION "This group is mandatory for devices which support the notifications/traps in vtpConfigNotificationsGroup3." GROUP vtpConfigNotificationsGroup2 DESCRIPTION "Implementation of this group is optional." GROUP vtpConfigNotificationsGroup3 DESCRIPTION "Implementation of this group is optional." GROUP vtpConfigNotificationsGroup4 DESCRIPTION "Implementation of this group is optional." GROUP vtpDiscoverGroup DESCRIPTION "This group is mandatory for devices which support the VTP discovery." GROUP vtpDatabaseGroup DESCRIPTION "This group is mandatory for devices which support the VTP distribution of different database types." GROUP vtpAuthGroup DESCRIPTION "This group is mandatory for devices which support asymmetric keys authentication mechanism for VTP." GROUP vtpInternalVlanGrp DESCRIPTION "Implementation of this group is optional." GROUP vlanStatsGroup DESCRIPTION "This group is mandatory for agents capable of providing VLAN statistics information." GROUP vtpConfigNotificationsGroup6 DESCRIPTION "Implementation of this group is optional." GROUP vtpConfigNotificationsGroup7 DESCRIPTION "Implementation of this group is optional." GROUP vtpTrunkPruningGroup3 DESCRIPTION "This group is mandatory for devices which support operational VTP pruning state." GROUP vtpConfigNotificationsGroup8 DESCRIPTION "This group is mandatory for devices which support the notification generation on operational VTP pruning state change." OBJECT vtpNotificationsEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanCreatedNotifEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanDeletedNotifEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainLocalMode MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainTftpServer MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainTftpPathname MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainPruningState MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainVersionInUse MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpInternalVlanAllocPolicy MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditOperation MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditBufferOwner MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditConfigRevNumber MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditState MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditMtu MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditDot10Said MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditRingNumber MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditBridgeNumber MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditStpType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditParentVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditRowStatus SYNTAX INTEGER { active(1) } WRITE-SYNTAX INTEGER { createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "Write access is not required. Support for createAndWait and notInService is not required." OBJECT vtpVlanEditTranslationalVlan1 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditTranslationalVlan2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditBridgeType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditAreHopCount MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditSteHopCount MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditIsCRFBackup MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditTypeExt2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortManagementDomain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortVlansEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortNativeVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortVlansPruningEligible MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortDynamicState MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortVtpEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortVlansEnabled2k MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortVlansEnabled3k MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortVlansEnabled4k MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlansPruningEligible2k MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlansPruningEligible3k MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlansPruningEligible4k MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortSetSerialNo MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpDiscoverAction MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpDatabaseLocalMode MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpDatabaseTakeOverPrimary MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpDatabaseTakeOverPassword MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpAuthPassword MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpAuthPasswordType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpAuthSecretKey MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { vtpMIBCompliances 14 } vtpMIBCompliance15 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for VTP implementations." MODULE -- this module MANDATORY-GROUPS { vtpBasicGroup, vtpVlanInfoGroup, vtpConfigNotificationsGroupRev1, vtpStatsGroup, vtpTrunkPortGroup, vtpVersion2BasicGroup, vtpNotificationObjectsGroup } GROUP vtpTrunkPruningGroup DESCRIPTION "Implementation of this group is optional." GROUP vtpTrunkPruningGroup2 DESCRIPTION "Implementation of this group is optional." GROUP vtpTrunkPortGroup2 DESCRIPTION "Implementation of this group is optional." GROUP vtpVlanInfoEditGroup DESCRIPTION "This group must be implemented by VTP Servers. VTP Clients need not implement these objects, and must not allow VLANs to be created, modified, or destroyed using these objects." GROUP vtpTrunkPortGroup3 DESCRIPTION "Implementation of this group is optional." GROUP vtp4kVlanGroupRev1 DESCRIPTION "This group must be implemented by the VTP Servers which support the range of VlanIndex between 1024 and 4095." GROUP vtpVlanIfIndexGroup DESCRIPTION "This group is an optional group containing objects providing information about the mapping of VLAN ID to its corresponding IfIndex." GROUP vtpVlanInfoEditGroup2 DESCRIPTION "This group is mandatory for devices which only support one VLAN editing for each 'apply' operation." GROUP vtpVlanNotifEnabledGroup DESCRIPTION "This group is mandatory for devices which support the notifications/traps in vtpConfigNotificationsGroup3." GROUP vtpConfigNotificationsGroup2 DESCRIPTION "Implementation of this group is optional." GROUP vtpConfigNotificationsGroup3 DESCRIPTION "Implementation of this group is optional." GROUP vtpConfigNotificationsGroup4 DESCRIPTION "Implementation of this group is optional." GROUP vtpDiscoverGroup DESCRIPTION "This group is mandatory for devices which support the VTP discovery." GROUP vtpDatabaseGroup DESCRIPTION "This group is mandatory for devices which support the VTP distribution of different database types." GROUP vtpAuthGroup DESCRIPTION "This group is mandatory for devices which support asymmetric keys authentication mechanism for VTP." GROUP vtpInternalVlanGrp DESCRIPTION "Implementation of this group is optional." GROUP vlanStatsGroup DESCRIPTION "This group is mandatory for agents capable of providing VLAN statistics information." GROUP vtpConfigNotificationsGroup6 DESCRIPTION "Implementation of this group is optional." GROUP vtpConfigNotificationsGroup7 DESCRIPTION "Implementation of this group is optional." GROUP vtpTrunkPruningGroup3 DESCRIPTION "This group is mandatory for devices which support operational VTP pruning state." GROUP vtpConfigNotificationsGroup8 DESCRIPTION "This group is mandatory for devices which support the notification generation on operational VTP pruning state change." GROUP vlanTrunkPortActiveVlansGroup DESCRIPTION "This group is mandatory for devices capable of providing active vlans information for trunk capable ports." OBJECT vtpNotificationsEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanCreatedNotifEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanDeletedNotifEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainLocalMode MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainTftpServer MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainTftpPathname MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainPruningState MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainVersionInUse MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpInternalVlanAllocPolicy MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditOperation MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditBufferOwner MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditConfigRevNumber MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditState MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditMtu MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditDot10Said MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditRingNumber MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditBridgeNumber MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditStpType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditParentVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditRowStatus SYNTAX INTEGER { active(1) } WRITE-SYNTAX INTEGER { createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "Write access is not required. Support for createAndWait and notInService is not required." OBJECT vtpVlanEditTranslationalVlan1 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditTranslationalVlan2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditBridgeType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditAreHopCount MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditSteHopCount MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditIsCRFBackup MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditTypeExt2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortManagementDomain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortVlansEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortNativeVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortVlansPruningEligible MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortDynamicState MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortVtpEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortVlansEnabled2k MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortVlansEnabled3k MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortVlansEnabled4k MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlansPruningEligible2k MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlansPruningEligible3k MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlansPruningEligible4k MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortSetSerialNo MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpDiscoverAction MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpDatabaseLocalMode MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpDatabaseTakeOverPrimary MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpDatabaseTakeOverPassword MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpAuthPassword MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpAuthPasswordType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpAuthSecretKey MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { vtpMIBCompliances 15 } vtpMIBCompliance16 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for VTP implementations." MODULE -- this module MANDATORY-GROUPS { vtpBasicGroup, vtpVlanInfoGroup, vtpConfigNotificationsGroupRev1, vtpStatsGroup, vtpTrunkPortGroup, vtpVersion2BasicGroup, vtpNotificationObjectsGroup } GROUP vtpTrunkPruningGroup DESCRIPTION "Implementation of this group is optional." GROUP vtpTrunkPruningGroup2 DESCRIPTION "Implementation of this group is optional." GROUP vtpTrunkPortGroup2 DESCRIPTION "Implementation of this group is optional." GROUP vtpVlanInfoEditGroup DESCRIPTION "This group must be implemented by VTP Servers. VTP Clients need not implement these objects, and must not allow VLANs to be created, modified, or destroyed using these objects." GROUP vtpTrunkPortGroup3 DESCRIPTION "Implementation of this group is optional." GROUP vtp4kVlanGroupRev1 DESCRIPTION "This group must be implemented by the VTP Servers which support the range of VlanIndex between 1024 and 4095." GROUP vtpVlanIfIndexGroup DESCRIPTION "This group is an optional group containing objects providing information about the mapping of VLAN ID to its corresponding IfIndex." GROUP vtpVlanInfoEditGroup2 DESCRIPTION "This group is mandatory for devices which only support one VLAN editing for each 'apply' operation." GROUP vtpVlanNotifEnabledGroup DESCRIPTION "This group is mandatory for devices which support the notifications/traps in vtpConfigNotificationsGroup3." GROUP vtpConfigNotificationsGroup2 DESCRIPTION "Implementation of this group is optional." GROUP vtpConfigNotificationsGroup3 DESCRIPTION "Implementation of this group is optional." GROUP vtpConfigNotificationsGroup4 DESCRIPTION "Implementation of this group is optional." GROUP vtpDiscoverGroup DESCRIPTION "This group is mandatory for devices which support the VTP discovery." GROUP vtpDatabaseGroup DESCRIPTION "This group is mandatory for devices which support the VTP distribution of different database types." GROUP vtpAuthGroup DESCRIPTION "This group is mandatory for devices which support asymmetric keys authentication mechanism for VTP." GROUP vtpInternalVlanGrp DESCRIPTION "Implementation of this group is optional." GROUP vlanStatsGroup DESCRIPTION "This group is mandatory for agents capable of providing VLAN statistics information." GROUP vtpConfigNotificationsGroup6 DESCRIPTION "Implementation of this group is optional." GROUP vtpConfigNotificationsGroup7 DESCRIPTION "Implementation of this group is optional." GROUP vtpTrunkPruningGroup3 DESCRIPTION "This group is mandatory for devices which support operational VTP pruning state." GROUP vtpConfigNotificationsGroup8 DESCRIPTION "This group is mandatory for devices which support the notification generation on operational VTP pruning state change." GROUP vlanTrunkPortActiveVlansGroup DESCRIPTION "This group is mandatory for devices capable of providing active VLANs information for trunk capable ports." GROUP vtpSourceInterfaceGroup DESCRIPTION "This group is mandatory for devices which support the VTP IP updater address preferred source interface." GROUP vtpConfigFileGroup DESCRIPTION "This group is mandatory for devices which support the location of VTP configuration file." GROUP vtpVlanLocalShutdownGroup DESCRIPTION "This group is mandatory for devices which support the vlan local shutdown feature." GROUP vtpLocalUpdaterGroup DESCRIPTION "This group is mandatory for devices which support the local updater IP address feature." GROUP vtpDeviceIdGroup DESCRIPTION "This group is mandatory for devices which support the device identifier used by VTP domain." OBJECT vtpNotificationsEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanCreatedNotifEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanDeletedNotifEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainLocalMode MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainTftpServer MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainTftpPathname MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainPruningState MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainVersionInUse MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpInternalVlanAllocPolicy MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditOperation MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditBufferOwner MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditConfigRevNumber MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditState MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditMtu MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditDot10Said MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditRingNumber MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditBridgeNumber MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditStpType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditParentVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditRowStatus SYNTAX INTEGER { active(1) } WRITE-SYNTAX INTEGER { createAndGo(4), destroy(6) } MIN-ACCESS read-only DESCRIPTION "Write access is not required. Support for createAndWait and notInService is not required." OBJECT vtpVlanEditTranslationalVlan1 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditTranslationalVlan2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditBridgeType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditAreHopCount MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditSteHopCount MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditIsCRFBackup MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanEditTypeExt2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortManagementDomain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortVlansEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortNativeVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortVlansPruningEligible MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortDynamicState MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortVtpEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortVlansEnabled2k MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortVlansEnabled3k MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortVlansEnabled4k MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlansPruningEligible2k MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlansPruningEligible3k MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlansPruningEligible4k MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortSetSerialNo MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpDiscoverAction MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpDatabaseLocalMode MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpDatabaseTakeOverPrimary MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpDatabaseTakeOverPassword MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpAuthPassword MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpAuthPasswordType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpAuthSecretKey MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainAdminSrcIf MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT managementDomainConfigFile MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vtpVlanLocalShutdown MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { vtpMIBCompliances 16 } -- units of conformance vtpBasicGroup OBJECT-GROUP OBJECTS { vtpVersion, vtpMaxVlanStorage, vtpNotificationsEnabled, managementDomainName, managementDomainLocalMode, managementDomainConfigRevNumber, managementDomainLastUpdater, managementDomainLastChange, managementDomainTftpServer, managementDomainTftpPathname, managementDomainRowStatus } STATUS current DESCRIPTION "A collection of objects providing basic status and control of a VTP implementation." ::= { vtpMIBGroups 1 } vtpVlanInfoGroup OBJECT-GROUP OBJECTS { vtpVlanState, vtpVlanType, vtpVlanName, vtpVlanMtu, vtpVlanDot10Said, vtpVlanRingNumber, vtpVlanBridgeNumber, vtpVlanStpType, vtpVlanParentVlan, vtpVlanTranslationalVlan1, vtpVlanTranslationalVlan2, vtpVlanBridgeType, vtpVlanAreHopCount, vtpVlanSteHopCount, vtpVlanIsCRFBackup } STATUS current DESCRIPTION "A collection of objects for monitoring VLAN information." ::= { vtpMIBGroups 13 } vtpVlanInfoEditGroup OBJECT-GROUP OBJECTS { vtpVlanEditOperation, vtpVlanApplyStatus, vtpVlanEditBufferOwner, vtpVlanEditConfigRevNumber, vtpVlanEditState, vtpVlanEditType, vtpVlanEditName, vtpVlanEditMtu, vtpVlanEditDot10Said, vtpVlanEditRingNumber, vtpVlanEditBridgeNumber, vtpVlanEditStpType, vtpVlanEditParentVlan, vtpVlanEditRowStatus, vtpVlanEditTranslationalVlan1, vtpVlanEditTranslationalVlan2, vtpVlanEditBridgeType, vtpVlanEditAreHopCount, vtpVlanEditSteHopCount, vtpVlanEditIsCRFBackup } STATUS current DESCRIPTION "A collection of objects for editing VLAN information in VTP Servers." ::= { vtpMIBGroups 14 } vtpStatsGroup OBJECT-GROUP OBJECTS { vtpInSummaryAdverts, vtpInSubsetAdverts, vtpInAdvertRequests, vtpOutSummaryAdverts, vtpOutSubsetAdverts, vtpOutAdvertRequests, vtpConfigRevNumberErrors, vtpConfigDigestErrors } STATUS current DESCRIPTION "A collection of objects providing VTP statistics." ::= { vtpMIBGroups 4 } vtpTrunkPortGroup OBJECT-GROUP OBJECTS { vlanTrunkPortManagementDomain, vlanTrunkPortEncapsulationType, vlanTrunkPortVlansEnabled, vlanTrunkPortNativeVlan, vlanTrunkPortRowStatus, vlanTrunkPortSetSerialNo } STATUS current DESCRIPTION "A collection of objects providing information on trunk ports." ::= { vtpMIBGroups 5 } vtpTrunkPortGroup2 OBJECT-GROUP OBJECTS { vlanTrunkPortDynamicState, vlanTrunkPortDynamicStatus, vlanTrunkPortVtpEnabled } STATUS current DESCRIPTION "Additional functionality added to the vlanTrunkPortTable." ::= { vtpMIBGroups 11 } vtpTrunkPortGroup3 OBJECT-GROUP OBJECTS { vlanTrunkPortEncapsulationOperType } STATUS current DESCRIPTION "Additional functionality added to the vlanTrunkPortTable." ::= { vtpMIBGroups 15 } vtpTrunkPruningGroup OBJECT-GROUP OBJECTS { vlanTrunkPortInJoins, vlanTrunkPortOutJoins, vlanTrunkPortOldAdverts, vlanTrunkPortVlansPruningEligible, vlanTrunkPortVlansXmitJoined, vlanTrunkPortVlansRcvJoined } STATUS current DESCRIPTION "A collection of objects providing information on VLAN pruning." ::= { vtpMIBGroups 7 } vtpTrunkPruningGroup2 OBJECT-GROUP OBJECTS { managementDomainPruningState } STATUS current DESCRIPTION "A collection of object providing information on whether VLAN pruning is enabled." ::= { vtpMIBGroups 10 } vtpVersion2BasicGroup OBJECT-GROUP OBJECTS { managementDomainVersionInUse } STATUS current DESCRIPTION "The object required to indicate the version of VTP in use by a management domain." ::= { vtpMIBGroups 12 } vtpConfigNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { vtpConfigDigestError, vtpConfigRevNumberError, vtpServerDisabled, vtpMtuTooBig, vtpVersionOneDeviceDetected, vlanTrunkPortDynamicStatusChange } STATUS deprecated DESCRIPTION "The notifications which a VTP implementation is required to implement. vtpConfigNotificationsGroup object is superseded by vtpConfigNotificationsGroupRev1, vtpConfigNotificationsGroup5." ::= { vtpMIBGroups 6 } vtp4kVlanGroup OBJECT-GROUP OBJECTS { vtpVlanTypeExt, vtpVlanEditTypeExt, vlanTrunkPortVlansEnabled2k, vlanTrunkPortVlansEnabled3k, vlanTrunkPortVlansEnabled4k, vtpVlansPruningEligible2k, vtpVlansPruningEligible3k, vtpVlansPruningEligible4k, vlanTrunkPortVlansXmitJoined2k, vlanTrunkPortVlansXmitJoined3k, vlanTrunkPortVlansXmitJoined4k, vlanTrunkPortVlansRcvJoined2k, vlanTrunkPortVlansRcvJoined3k, vlanTrunkPortVlansRcvJoined4k } STATUS deprecated DESCRIPTION "A collection of objects providing information for VLANS with VlanIndex from 1024 to 4095. vtp4kVlanGroup object is superseded by vtp4kVlanGroupRev1." ::= { vtpMIBGroups 16 } vtpDot1qTunnelGroup OBJECT-GROUP OBJECTS { vlanTrunkPortsDot1qTag, vlanTrunkPortDot1qTunnel } STATUS deprecated DESCRIPTION "A collection of objects providing information for dot1qtunnel feature. vtpDot1qTunnelGroup object is superseded by vtpDot1qTunnelGroup2." ::= { vtpMIBGroups 17 } vtpVlanIfIndexGroup OBJECT-GROUP OBJECTS { vtpVlanIfIndex } STATUS current DESCRIPTION "A collection of objects providing information for mapping of VLAN ID to its corresponding ifIndex." ::= { vtpMIBGroups 18 } vtpVlanInfoEditGroup2 OBJECT-GROUP OBJECTS { vtpVlanEditModifiedVlan } STATUS current DESCRIPTION "A collection of objects for editing VLAN information when only one VLAN is allowed to be edited for each 'apply' operation." ::= { vtpMIBGroups 19 } vtp4kVlanGroupRev1 OBJECT-GROUP OBJECTS { vtpVlanTypeExt, vtpVlanEditTypeExt2, vlanTrunkPortVlansEnabled2k, vlanTrunkPortVlansEnabled3k, vlanTrunkPortVlansEnabled4k, vtpVlansPruningEligible2k, vtpVlansPruningEligible3k, vtpVlansPruningEligible4k, vlanTrunkPortVlansXmitJoined2k, vlanTrunkPortVlansXmitJoined3k, vlanTrunkPortVlansXmitJoined4k, vlanTrunkPortVlansRcvJoined2k, vlanTrunkPortVlansRcvJoined3k, vlanTrunkPortVlansRcvJoined4k } STATUS current DESCRIPTION "A collection of objects providing information for VLANS with VlanIndex from 1024 to 4095." ::= { vtpMIBGroups 20 } vtpNotificationObjectsGroup OBJECT-GROUP OBJECTS { vtpVlanPortLocalSegment } STATUS current DESCRIPTION "A collection of objects included in VTP notifications." ::= { vtpMIBGroups 21 } vtpDot1qTunnelGroup2 OBJECT-GROUP OBJECTS { vlanTrunkPortsDot1qTag } STATUS deprecated DESCRIPTION "A collection of objects providing information for dot1qtunnel feature." ::= { vtpMIBGroups 22 } vtpConfigNotificationsGroup2 NOTIFICATION-GROUP NOTIFICATIONS { vtpLocalModeChanged, vtpVersionInUseChanged } STATUS current DESCRIPTION "The notifications which a VTP implementation is required to implement." ::= { vtpMIBGroups 23 } vtpVlanNotifEnabledGroup OBJECT-GROUP OBJECTS { vtpVlanCreatedNotifEnabled, vtpVlanDeletedNotifEnabled } STATUS current DESCRIPTION "A collection of objects to indicate whether a certain group of notifications are enabled." ::= { vtpMIBGroups 24 } vtpConfigNotificationsGroup3 NOTIFICATION-GROUP NOTIFICATIONS { vtpVlanCreated, vtpVlanDeleted } STATUS current DESCRIPTION "The notifications implemented by a device which supports these features." ::= { vtpMIBGroups 25 } vtpConfigNotificationsGroup4 NOTIFICATION-GROUP NOTIFICATIONS { vtpVlanRingNumberConflict } STATUS current DESCRIPTION "The notifications implemented by a device which supports these features." ::= { vtpMIBGroups 26 } vtpDiscoverGroup OBJECT-GROUP OBJECTS { vtpDiscoverAction, vtpDiscoverStatus, vtpLastDiscoverTime, vtpDiscoverResultIndex, vtpDiscoverResultDatabaseName, vtpDiscoverResultConflicting, vtpDiscoverResultDeviceId, vtpDiscoverResultPrimaryServer, vtpDiscoverResultRevNumber, vtpDiscoverResultSystemName } STATUS current DESCRIPTION "A collection of objects providing information of VTP discovery." ::= { vtpMIBGroups 27 } vtpDatabaseGroup OBJECT-GROUP OBJECTS { vtpDatabaseName, vtpDatabaseLocalMode, vtpDatabaseRevNumber, vtpDatabasePrimaryServer, vtpDatabasePrimaryServerId, vtpDatabaseTakeOverPrimary, vtpDatabaseTakeOverPassword } STATUS current DESCRIPTION "A collection of objects providing information of VTP databases." ::= { vtpMIBGroups 28 } vtpAuthGroup OBJECT-GROUP OBJECTS { vtpAuthPassword, vtpAuthPasswordType, vtpAuthSecretKey } STATUS current DESCRIPTION "A collection of objects providing information of VTP authentication mechanism." ::= { vtpMIBGroups 29 } vtpConfigNotificationsGroupRev1 NOTIFICATION-GROUP NOTIFICATIONS { vtpConfigDigestError, vtpConfigRevNumberError, vtpVersionOneDeviceDetected, vlanTrunkPortDynamicStatusChange } STATUS current DESCRIPTION "The notifications which a VTP implementation is required to implement." ::= { vtpMIBGroups 30 } vtpConfigNotificationsGroup5 NOTIFICATION-GROUP NOTIFICATIONS { vtpServerDisabled, vtpMtuTooBig } STATUS deprecated DESCRIPTION "The additional notifications that may be related to a VTP implementation. vtpConfigNotificationsGroup5 object is superseded by vtpConfigNotificationsGroup6, vtpConfigNotificationsGroup7." ::= { vtpMIBGroups 31 } vtpInternalVlanGrp OBJECT-GROUP OBJECTS { vtpInternalVlanAllocPolicy, vtpInternalVlanOwner } STATUS current DESCRIPTION "A collection of objects providing information of internal VLANs." ::= { vtpMIBGroups 32 } vlanStatsGroup OBJECT-GROUP OBJECTS { vlanStatsVlans, vlanStatsExtendedVlans, vlanStatsInternalVlans, vlanStatsFreeVlans } STATUS current DESCRIPTION "A collection of objects providing VLAN statistics information in the system." ::= { vtpMIBGroups 33 } vtpConfigNotificationsGroup6 NOTIFICATION-GROUP NOTIFICATIONS { vtpServerDisabled } STATUS current DESCRIPTION "The additional notifications that may be related to a VTP implementation." ::= { vtpMIBGroups 34 } vtpConfigNotificationsGroup7 NOTIFICATION-GROUP NOTIFICATIONS { vtpMtuTooBig } STATUS current DESCRIPTION "The additional notifications that may be related to a VTP implementation." ::= { vtpMIBGroups 35 } vtpTrunkPruningGroup3 OBJECT-GROUP OBJECTS { managementDomainPruningStateOper } STATUS current DESCRIPTION "A collection of objects providing information on operational VTP pruning state in a manamgement domain." ::= { vtpMIBGroups 36 } vtpConfigNotificationsGroup8 NOTIFICATION-GROUP NOTIFICATIONS { vtpPruningStateOperChange } STATUS current DESCRIPTION "The additional notifications for operational VTP pruning state change in a management domain." ::= { vtpMIBGroups 37 } vlanTrunkPortActiveVlansGroup OBJECT-GROUP OBJECTS { vlanTrunkPortVlansActiveFirst2k, vlanTrunkPortVlansActiveSecond2k } STATUS current DESCRIPTION "A collection of objects providing active vlan information for a trunking port in a management domain." ::= { vtpMIBGroups 38 } vtpSourceInterfaceGroup OBJECT-GROUP OBJECTS { managementDomainAdminSrcIf, managementDomainSourceOnlyMode, managementDomainOperSrcIf } STATUS current DESCRIPTION "A collection of object providing the preferred source interface for the VTP IP updater address." ::= { vtpMIBGroups 39 } vtpConfigFileGroup OBJECT-GROUP OBJECTS { managementDomainConfigFile } STATUS current DESCRIPTION "A collection of object providing the location of VTP configuration file." ::= { vtpMIBGroups 40 } vtpVlanLocalShutdownGroup OBJECT-GROUP OBJECTS { vtpVlanLocalShutdown } STATUS current DESCRIPTION "A collection of object providing the VLAN local shutdown state." ::= { vtpMIBGroups 41 } vtpLocalUpdaterGroup OBJECT-GROUP OBJECTS { managementDomainLocalUpdaterType, managementDomainLocalUpdater } STATUS current DESCRIPTION "A collection of object providing the local updater IP address." ::= { vtpMIBGroups 42 } vtpDeviceIdGroup OBJECT-GROUP OBJECTS { managementDomainDeviceID } STATUS current DESCRIPTION "A collection of object providing the device id." ::= { vtpMIBGroups 43 } END